(c)
Use two bolts and washers to install the forward adapter (-19) at the attach point nearest the middle locking actuator.
NOTE: Attach the adapter with the smaller hole inboard and
____ the slot outboard, in relation to the nacelle centerline. Turn the adapter the opposite direction if it hits the torque box fittings.
(d)
Use two bolts and washers to install the aft adapter (-20) to the aft attach point on the fan duct cowl.
(e)
Attach the rounded beam (-3) to the forward adapters with three quick release pins.
(f)
Attach the straight beam (-2) to the rounded beam (-3).
(g)
Attach the straight beam (-2) to the cable of the aft adapter (-20).
(h)
Attach the hoist cable to the straight beam (-2).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
78-31-00
ALL ú ú N01 Page 217 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES /MAINTENANCE MANUAL ////////////////////////
AFT ADAPTER (-20)
SEE A
FORWARD ADAPTER (-18)
NACELLE ZONE
VENTILATION
VALVE SENSE
LINE
45`
STRAIGHT BEAM (-2)
A
CURVED BEAM (-3)
FORWARD ADAPTER (-19)
A
LEFT THRUST REVERSER
SLING INSTALLATION
(RIGHT SIDE IS EQUIVALENT)
A
STRAIGHT BEAM (-2)
CURVED
BEAM (-3)
QUICK-
RELEASE
PINS
FORWARD
ADAPTER (-19) THRUST (-20) AFT ADAPTER
REVERSER
A-A
Thrust Reverser Sling
Figure 204
M49443
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
78-31-00
ALL ú ú N01 Page 218 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
S 012-049-N00
CAUTION:_______ DO NOT LIFT OR MOVE THE THRUST REVERSER HALF IF MORE THAN SIX
OF THE CASCADE VANE SEGMENTS ARE NOT THERE. THREE CASCADE VANE
SEGMENTS MUST BE INSTALLED. DAMAGE TO THE THRUST REVERSER
STRUCTURE CAN OCCUR.
(15) Open the thrust reverser (Fig. 203):
NOTE: The cascade vane segments must be equally put apart on
____ the thrust reverser structure. There cannot be more than two adjacent open spaces between the segments.
(a) Apply sufficient force to lift the sling and open the thrust reverser half until it is half open.
S 492-050-N00
(16) Do these steps to install the hold-open rod:
(a)
Disconnect the bottom end of the hold-open rod from the bracket on the thrust reverser.
(b)
Extend the hold-open rod to engage the support bracket at the 23-degree (bottom) or the 45-degree (top) position on the engine fan case.
(c)
Continue to operate the hoist to lift the thrust reverser until the hold-open rod locks in the fully extended position.
NOTE: If you install the hold-open rod in the bracket at
____ the 45-degree position, it is usually necessary to manually push up on the thrust reverser to fully extend and lock the hold-open rod.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
78-31-00
ALL ú ú N01 Page 219 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
S 212-051-N00
WARNING:_______ MAKE SURE THE HOLD-OPEN ROD IS FULLY EXTENDED AND LOCKED BEFORE
YOU MOVE BETWEEN THE ENGINE AND THE OPEN THRUST REVERSER. THE
THRUST REVERSER IS HEAVY AND CAN FALL CLOSED QUICKLY IF THE
HOIST OR THE SLING EQUIPMENT HAS A FAILURE. THIS CAN CAUSE
INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
WARNING: DO NOT PUT YOUR WEIGHT ON A THRUST REVERSER THAT IS KEPT OPEN 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 EXHAUST 1(45)
