(2)  
Remove the four rivets from the base. Refer to the Structural Repair Manual.

 S 032-024

 (3)  
Put a sharp broad-based knife below the edge of the base and remove the base from the airplane skin.

 G.  Remove the Static Discharger Base from the Aileron:
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 23-61-01
 ALL  ú ú 01 Page 211 ú Sep 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 S 032-036
 CAUTION: BE CAREFUL NOT TO DAMAGE THE AILERON SURFACE.
_______
 (1)  
Use the sealing compound cutting tool to remove the weather/aerodynamic fillet seal around the edge of the base.

 S 032-026

 (2)  
Remove the four screws from the static discharger base.

 S 022-027

 (3)  
Put a sharp broad-based knife below the edge of the base and remove the base from the airplane skin.

 H. Remove the Static Discharger Base from the Adapter Assembly:
 S 032-038
 CAUTION: BE CAREFUL NOT TO DAMAGE THE ADAPTER ASSEMBLY AND FLIGHT
_______
 CONTROL SURFACE.

 (1)  
Use the sealing compound cutting tool to remove the weather/aerodynamic fillet seal around the edge of the base.

 S 032-030

 (2)  
Remove the four rivets from the base. Refer to the Structural Repair Manual.

 S 022-031

 (3)  
Put a sharp broad-based knife below the edge of the base and remove the base from the adapter assembly.

 TASK 23-61-01-402-028
 7. Static Discharger Base Installation (Fig. 202)
___________________________________
 A. References
 (1)  SRM 51-20-01
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 23-61-01
 ALL  ú ú 01 Page 212 ú May 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 B. Equipment
 (1)  
Bonding meter (SWPM 20-20-00)

 (2)  
Sealing gun - 6 inch length cartridge - Commerically available

 (3)  
Varnish brush - 1 or 2 inch - Commercially available

 (4)  
Sealing compound cutting tool - hardwood or plexiglass -Commerically available

 C. Consumable Material
 (1)  
B00136 Naphta TT-N-95A, Aliphatic

 (2)  
B00193 Sealant - Chromate type BMS 5-95

 (3)  
A00247 Cheesecloth - BMS 15-5 (Ref 20-30-07)

 (4)  
G00033 Scotch Brite Type A - 3M Company

 (5)  
G02124 Sandpaper - 250 Grit

 D. Access
 (1)  Location Zones
 500/600 Left Wing/Right Wing
 300 Empennage and Body Section 48

 E. Prepare to Install the Discharger Base:
 S 032-032
 (1)  
Remove sealant from bonding area (skin surface or adapter assembly) use the sealing compound cutting tool.

 S 002-033

 (2)  
Remove the static discharger base from the container. Make sure the discharger mounting surface is correct for the installation.

 S 122-034

 (3)  
Make the graphite and titanium bonding surfaces rough with 250 grit sandpaper until black dust shows.

 S 112-035
 WARNING:_______KEEP SOLVENTS AWAY FROM OPEN FIRE. DO NOT GET THE SOLVENTS IN YOUR MOUTH, OR EYES, OR ON YOUR SKIN. DO NOT BREATHE THE FUMES FROM THE SOLVENTS. SOLVENTS CAN BE POISONOUS AND FLAMMABLE AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (4)  Clean and remove grease from the bonding areas. Use a clean wiper soaked with a clean solvent. Continue to use the clean wipers until there is no unwanted material.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 23-61-01
 ALL  ú ú 01 Page 213 ú May 28/01
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 COMMUNICATIONS 通訊(121)