D.  
Overhead Distribution Duct Removal

 S 024-066
 (1)  
Disconnect the flex sleeves (2) between the distribution duct (1) and the plenum/nozzle assembly (4) as follows:

 (a)  
Loosen the clamps (5) that hold the flex sleeves (2) to the distribution duct (1).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-23-01
 ALL  ú ú 01 Page 401 ú May 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

DISTRIBUTION DUCT
(DETAIL REMOVED FOR CLARITY)

SEE A
FWD
PASSENGER COMPARTMENT
11. DIFFUSER/HOSE  ASSEMBLY
1. DISTRIBUTION DUCT
10. TAPE
2. FLEX SLEEVE
3. CLAMP (2 LOCATIONS)
9. BRACKET
 ASSEMBLY

4. STRAP
5.
 CLAMP  (2 LOCATIONS)

6.
 FLEX SLEEVE

8. PLENUM/NOZZLE
 ASSEMBLY

7. ORIFICE
 ASSEMBLY FWD
DISTRIBUTION DUCT
A

Passenger Cabin Overhead Air Distribution Duct Installation
Figure 401

M66051
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-23-01
 ALL  ú ú 01 Page 402 ú May 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 (b)  
Remove the ends of the flex sleeves (2) from the distribution duct (1).

 (c)  
Keep the orifice assemblies (3) to use with the replacement duct assembly.

 S 024-011
 (2)  
Remove the tape (6) that connects the diffuser/hose assemblies (7) to the distribution duct (1).

 S 024-012

 (3)  
Remove the straps (8) that hold the distribution duct (1) to the bracket assemblies (9).

 S 024-067

 (4)  
Loosen the clamps (10) that secure the flex sleeves (11) at each end of the distribution duct (1).

 S 024-068

 (5)  
Support the distribution duct (1) and slide the flex sleeves (11) away from the ends of the duct.

 S 024-069

 (6)  
Remove the distribution duct.

 TASK 21-23-01-214-070
 3.  Overhead Distribution Duct Installation (Fig. 401)_______________________________________
 A. References
 (1)  
AMM 21-23-01/201, Air Conditioning System Ducts

 (2)  
AMM 25-22-01/401, Sculptured Ceiling Panels

 (3)  
AMM 25-28-05/401, Center Overhead Storage Compartment

 (4)  
AMM 36-00-00/201, Pneumatics Systems

 B.
Access

 (1)  
Location Zones 233/234 Passenger cabin - Section 43 - Body Station 663.25 to Body Station 803.25

 C.
Overhead Distribution Duct Installation

 S 984-071
 (1)  
Put the distribution duct (1) in its position above the ceiling panels.

 S 424-030

 (2)  
Slide the flex sleeves (11) onto the ends of the distribution duct

 (1)
 as follows:

 (a)  
Make sure each flex sleeve (11) overlaps the duct end by 1.63 +/- 0.13 inches (41.4 +/- 3.3 mm).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-23-01
 ALL  ú ú 01 Page 403 ú May 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 (b)  Loosely position the duct clamps (10) 0.38 +/- 0.13 inches
 (9.65 +/- 3.3 mm) from the ends of the flex sleeves (11).
 S 424-034
 (3)  
Install the orifice assemblies (3) in the same locations from which they were removed.

 S 424-035

 (4)  
Install the flex sleeves (2) between the distribution duct (1) and the plenum/nozzle assembly (4) as follows:

 (a)  
Move the ends of the flex sleeves (2) over the nozzles on the distribution duct (1) with the orifice assemblies (3) in position.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 空調 AIR CONDITIONING 1(47)