EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-15-02
 ALL  ú ú 06 Page 405 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 S 434-033 CAUTION: THE TORQUE WRENCH MUST BE SET TO THE SPECIFIED TORQUE VALUE.
_______ AN INCORRECT VALUE CAN CAUSE DAMAGE TO THE CONNECTOR AND NO SUFFICIENT LIGHTNING PROTECTION FOR THE WIRES.
 (2)  
Tighten the bolts (2) to between 20 to 40 pound-inches.
 S 434-013

 CAUTION:_______DO NOT TWIST OR CAUSE A BEND TO THE DETECTOR ELEMENT. THIS CAN CAUSE DAMAGE TO THE ELEMENT.

 (3)  
Install the liners (8) on the detector element (9), and install the element (9) in the clamps (10).

 NOTE: Adjust the element so that it will hang over the opposite
____ end of the responder at a maximum of 1 inch.
 S 434-014
 (4)  
Close the clamps (10) and lock.
 S 034-015

 (5)  
Remove the protective cap and install the electrical connector.

 E.  AIRPLANES WITH GRAVINER FIRE DETECTORS; Install the detector element.
 S 424-031
 (1)  Put one electrical connector of the detector element through the hole in the end bracket of the support tube. Tighten with a retaining nut.
 S 434-016
 CAUTION: DO NOT TWIST OR CAUSE A SHARP BEND TO THE DETECTOR ELEMENT.
_______
 THIS CAN CAUSE DAMAGE TO ELEMENT.

 (2)  Install the detector element along the support tube. Make sure it is not too loose between the two clamps.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-15-02
 ALL  ú ú 01 Page 406 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 S 434-017
 (3)  
Install the liners on the detector element at the location of the mounting clamps.

 S 434-018

 (4)
Install the element with the liners in the clamps and tighten.

 S 434-019

 (5)  
Install the remaining electrical connector through the hole in the end bracket of the support tube. Tighten with a retaining nut.

 S 754-020

 (6)  
Make sure the resistance between the detector connector shell and the primary structure of the airplane is not more than 0.010 ohm.

 S 434-021

 (7)  
Use lockwire to lock the retaining nuts on the connector.

 S 034-022

 (8)  
Remove the protective caps from the airplane wire connectors and attach the connectors to the detector element connectors. Use new copper crush washers. Tighten the connectors to between 20 to 40 pound-inches.

 S 434-023

 (9)  
Use lockwire to lock the airplane wire connectors to the element connectors.

 S 414-024

 (10)
 Close the APU access doors.

 F. Do a Test of the Detector Element Installation:
 S 864-025
 (1)  Supply electrical power (AMM 24-22-00).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-15-02
 ALL  ú ú 03 Page 407 ú Mar 20/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 S 864-026
 (2)  On the pilot forward control stand, P9, do these steps: (a) Set the EICAS COMPUTER select switch to the AUTO position. (b) Set the EICAS display to STATUS.
 S 864-027
 (3)  Close the circuit breakers (6 places) on the P11 panel.
 S 034-028
 (4)  Remove the DO-NOT-CLOSE tags and close these circuit breakers on the P11 panel: (a) 11B24, FIRE DETECTION APU 1 (b) 11B25, FIRE DETECTION APU 2 (c) 11J25, FIRE DET ALTN PWR APU
 S 754-029
 (5)  Make sure these EICAS messages still show on the bottom display after momentary power-up: (a) APU FIRE LP 1 (b) APU FIRE LP 2
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 防火 FIRE PROTECTION 1(70)