(b)
Remove the applicable LRRA receiver/transmitter. To remove it, do this task: Low Range Radio Altimeter (LRRA) Receiver/Transmitter (R/T) Removal, AMM TASK 34-33-21-000-801.
(c)
Connect the TDR time domain reflectometer, COM-5187test set at pins 71 and C71 of the applicable connector at the LRRA receiver/transmitter (WDM 34-33-11, WDM 34-33-21).
EFFECTIVITY SIL ALL 34-33 TASK 808
D633A103-SIL BOEING PROPRIETARY -Copyright # Unpublished Work -See title page for details Page 216 Jun 15/2010
LRRA
TDR TEST SET CONNECTOR
LRRA-1 (M1735) TDR TEST SET D3667A
TDR --------------------pin71 TDR --------------------pinC71
LRRA-2 (M1736) TDR TEST SET D3669A
TDR --------------------pin71 TDR --------------------pinC71
(d)
Do an electrical check of the coaxial cable and the antenna.
NOTE: The TDR test set has instructions which tell how to do the check of the cable and antenna.
(e)
Disconnect the TDR test settime domain reflectometer, COM-5187.
(f)
Re-install the LRRA receiver/transceiver. To install it, do this task: Low Range Radio Altimeter (LRRA) Receiver/Transmitter (R/T) Installation, AMM TASK 34-33-21-400-801.
(g)
If you find a problem with the coaxial cable, then do these steps: 1) Replace the applicable coaxial cable (WDM 34-31-11). 2) Do
this
task:
Low
Range
Radio
Altimeter
(LRRA)
BITE
Procedure,
34-33
TASK
801.
3) If the red REC ANT FAIL light goes off, then you corrected the fault.
(h)
If you find a problem with the antenna, then do these steps:
1) Replace the applicable LRRA antenna.
These are the tasks:
Low Range Radio Altimeter (LRRA) Antenna Removal, AMM
TASK 34-33-11-000-801,
Low Range Radio Altimeter (LRRA) Antenna Installation, AMM
TASK 34-33-11-400-801. 2) Do
this
task:
Low
Range
Radio
Altimeter
(LRRA)
BITE
Procedure,
34-33
TASK
801.
3) If the red REC ANT FAIL light goes off, then you corrected the fault.
-------------------------END OF TASK ---------------------------801. Head Up Display BITE Procedure
EFFECTIVITY SIL ALL 34-33 TASK 808
D633A103-SIL BOEING PROPRIETARY -Copyright # Unpublished Work -See title page for details Page 217 Jun 15/2010
A. General
(1)
You do the Head Up Display (HUD) BITE test at the HUD control panel (HCP). The HUD control panel is on the aft P8 panel.
(a)
When you push the TEST switch on the HUD control panel, you turn on the test mode and the LED light on the TEST switch comes on. When you push the TEST switch again, you turn off the test mode and the LED light on the TEST switch goes off.
(b)
When you turn the test mode on, you start a HUD BITE check.
(c)
The HUD BITE does a test for 3 to 4 seconds. During the BITE the FAULT light on the HUD control panel is on and the MODE display line on the HUD control panel shows TEST. When the BITE is complete, the FAULT light goes off and you see symbols on the HUD combiner display, and TEST on the MODE display goes off.
(d)
If the HUD BITE finds a fault, the FAULT light stays on. The HUD control panel STBY display line shows the fault code. If there is more than one faults, the fault codes show in two second intervals.
中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-600/700/800/900 FAULT ISOLATION MANUAL 故障隔離手冊(cè) 導(dǎo)航(127)
