曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

The rotating shroud must be in close proximity to the blade tips within thetube. To get this proximity， a shaft-mounted plexiglass disc was suspended from above the blades. The plexiglass disc was machined as shown in Figure 7-13. The plexiglass tube was slotted so that the disc could be centered on the center line of the tube and its stepped section lowered through the two slots in the tube. Clearances between the slot edges and the disc were minimized.
FPO
Figure 7-12. Treatments on center cascade blade.
One slot was cut directly above the blade passage emplacement. The other slot was sealed off to prevent leakage. As the disc was lowered into closeproximity to the bladetips， the blade passage was completed. The clearancebetween disc and blade was kept at 0.035 of an inch. Thedisc， when spunfromabove， acted as the rotating shroud.
There are only two basic casing treatment designs other than a blank design.which corresponds to no casing treatment at all. The first type of casing treatment consists of radial grooves. A radial groove is a casing treatment design in which the groove is essentially parallel to the chordline of the blade. The second basic type is the circumferential groove. This type of casing treatment has its grooves perpendicular to the blade chordline. Figure 7-14 is a photograph of two discs showing the two types of casing

Figure 7-1.. Details of the various casing treatments. Each treatment was on a separate disc.
treatment used. The third disc used is ablank， representing the present type of casing. The results indicate that the radial casing treatment is most effective in reducing leakage and also in increasing the surge-to-stall margin. Figure 7-15 shows the leakage at the tips for the various casing treatments. Figure 7-16 shows the velocity patterns observed by the use of various casingtreatments. Note that for the treatment along the chord (radial)， the flow is maximum at the tip. This flow maximum at the tip indicates that the chance of rotor tip stall is greatly reduced.
Energ叩 Increases
In an axial flow compressor air passes from one stage to the next with each stage raising the pressure and temperature slightly. By producing low-pressure increases on the order of 1.1:1-1.4:1， very high efficiencies can be obtained. The use of multiple stages permits overall pressure increases up to
FPO
Figure 7-14. Two discs with casing treatment.

Figure 7-15. .ass flow leakage at tips for various casing treatments.

40:1. Figure 7-3 shows the pressure，velocity， and total enthalpy variation for flow through several stages of an axial flow compressor. It is important to note here that the changes in the totalconditions for pressure， temperature， and enthalpy occur only in the rotating component where energy is inputtedinto the system. As seen also in Figure7-3， the length of theblades， and theannulusarea， which is the area between the shaft and shroud， decreases through the length of the compressor. This reduction in flow area compen-sates for the increase in fluid density asit is compressed， permitting a constant axial velocity. In most preliminary calculations used in the designof a compressor， the average blade height is used as the blade height for the stage.
The rule of thumb for a multiple stage gas turbine compressor would bethat the energy rise per stage would be constant， rather than the commonly held perception that the pressure rise per stage is constant. The energy rise per stage can be written as:
 H二[H2 -H1l(7-6)
NS
where: H1， H2二 Inlet and Exit Enthalpy Btujlbm (k.jkg)
N，二 number of stages
Assuming that the gas is thermally and calorically perfect (句 ， and寸 are constant) equation 7-1 can be rewritten as:
 []寸-1
幾in PP12 寸 -1

 幾stage二N， (7-7)
where:幾in二 Inlet Temperature (oF， oC)
P1， P2二 Inlet and Exit Pressure (psia， bar)
Velocit叩 Triangles
As stated earlier， an axial-flow compressor operates on the principle of putting work into the incoming air by acceleration and diffusion. Air enters the rotor as shown in Figure 7-17 with an absolute velocity (V ) and an angle α1， which combines vectorially with the tangential velocity of the blade ( U ) to produce the resultant relative velocity W1 at an angle α2. Air flowing through the passages formed by the rotor blades is given a relative velocity W2 at an angle α4， which is less than α2 because of the camber of the blades. Note that W2 is less than W1， resulting from an increase in the passage widthas the blades become thinner toward the trailing edges. Therefore， some diffusion will take place in the rotor section of the stage. The combination of the relative exit velocity and blade velocity produce an absolute velocity V2at the exit of the rotor. The air then passes through the stator， where it is turned through an angle so that the air is directed into the rotor of the next stage with a minimum incidence angle. The air entering the rotor has an axial component at an absolute velocity Vz1 and a tangential component Ve1.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：燃氣渦輪工程手冊 Gas Turbine Engineering Handbook 2(16)