曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

MECHANICS / ELECTRICS & AVIONICS COURSE 25 EQUIPMENT/FURNISHINGS
UF94200
EFFECTIVITY Page 158
ALL
25 - EQUIPMENT/FURNISHING
25-61-00 PASSENGER DOOR ESCAPE SLIDE RAFT
DISCONNECTION.
CONTENTS:
PASSENGER DOOR ESCAPE SLIDE RAFT DISCONNECTION.
TMUESRG01 LEVEL 3
EFFECTIVITY 25-61-00 Page 1
Oct 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 25 EQUIPMENT/FURNISHINGS
UF94200
EFFECTIVITY Page 159
ALL
PASSENGER DOOR ESCAPE SLIDE RAFT DISCONNECTION.
PASSENGER DOOR ESCAPE SLIDE RAFT DISCONNECTION.
Disconnect the pack-assembly electrical supply.
The quick-disconnect connector is installed below the
cable routing velcro.
Open the girt flap.
Open the lanyard velcro and remove the survival kit
attach-loop from the telescopic end fitting of the
girt bar.
Open the blue and the green velcros and separate the
survival kit lanyard and the girt bar release-strap.
Remove the girt bar release-strap from the girt bar
release-lever.
Pull the mooring line from the girt pocket and support
the escape slide raft with the mooring line.
Pull the release handle, release the mooring line
slowly and let the girt lace-up joint and the girt
assembly release from the girt bar.
Carefully lower the escape slide raft to the ground.
Make sure that you do not damage the reservoir when
you lower the slide raft to the ground.
Hold the girt bar and push in the girt bar release-lever
by hand.
Remove the girt bar from the floor attach fittings.
Remove the mooring line loop-end from the girt bar and
keep the girt bar with the aircraft.
Lift the empty pack assembly soft-cover clear of the
passenger/crew door and close the door.
Remove the pack assembly decorative-cover and keep it
with the aircraft.
Loosen the link nut and remove and retain the attach
link and the pull-handle from the stud assembly.
Remove the stud assemblies, with the allen key, from
the door attach anchor nuts.
Move the packboard inboard on its supports and hold
it.
Disconnect the pack assembly connector from the
electrical connector installed on the passenger/crew
door.
Remove the packboard from the passenger crew door
supports.
Service the door damper and emergency operation
cylinder.
TMUESRG01-T01 LEVEL 3
EFFECTIVITY 25-61-00 Page 2
Oct 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 25 EQUIPMENT/FURNISHINGS
UF94200
EFFECTIVITY Page 160
ALL
PASSENGER DOOR ESCAPE SLIDE RAFT DISCONNECTION.
TMUESRG01-P01 LEVEL 3
EFFECTIVITY 25-61-00 Page 3
Oct 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 25 EQUIPMENT/FURNISHINGS
UF94200
EFFECTIVITY Page 161
ALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUESRG01 LEVEL 3
EFFECTIVITY 25-61-00 Page 4
Oct 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 25 EQUIPMENT/FURNISHINGS
UF94200
EFFECTIVITY Page 162
ALL
25 - EQUIPMENT/FURNISHING
25-61-00 PASSENGER DOOR ESCAPE SLIDE RAFT
INSTALLATION.
CONTENTS :
PASSENGER DOOR ESCAPE SLIDE RAFT INSTALLATION.
TMUESRA01 LEVEL 3
EFFECTIVITY 25-61-00 Page 1
Oct 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 25 EQUIPMENT/FURNISHINGS
UF94200
EFFECTIVITY Page 163
ALL
PASSENGER DOOR ESCAPE SLIDE RAFT INSTALLATION.
PASSENGER DOOR ESCAPE SLIDE RAFT INSTALLATION.
Make sure that the operation striker lever of the door
damper and emergency operation cylinder is in the
DISARMED position.
Make sure that the passenger/crew door on which you
will install the pack assembly is closed and locked.
Make sure that the emergency control handle is in the
DISARMED position and that the safety pin is installed.
Make sure that the lockpin assembly is installed in
the operating head of the slide raft inflation
reservoir.
Check the pack electrical supply-cable, and make sure
that the cable is installed for the left door or the
right door as required.
Make sure that the short girt flap is on the top of
the long girt flap.
Attach a temporary tie to the small cord loop.
Put the girt bar in place.
Make sure that the girt bar end fittings point away
from the slide raft pack, and that the telescopic end
is in the forward position in relation to the aircraft.
Install the mooring line loop on the girt bar rear
end.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：ATA 25 EQUIPMENT AND FURNISHINGS(21)