曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

runway length requirements:
a) if a stopway is economically possible, the lengths to be
provided are those for the balanced field length. The
runway length is the take-off run required or the landing
distance required, whichever is the greater. If the
accelerate-stop distance required is greater than the
runway length so determined, the excess may be
provided as stopway, usually at each end of the runway.
In addition, a clearway of the same length as the
stopway must also be provided;
b) if a stopway is not to be provided, the runway length is
the landing distance required, or if it is greater, the
accelerate-stop distance required, which corresponds to
the lowest practical value of the decision speed. The
excess of the take-off distance required over the runway
length may be provided as clearway, usually at each end
of the runway.
2.9 In addition to the above consideration, the concept of
clearways in certain circumstances can be applied to a
situation where the take-off distance required for all engines
operating exceeds that required for the engine failure case.
2.10 The economy of a stopway can be entirely lost if, after
each usage, it must be regraded and compacted. Therefore, it
should be designed to withstand at least a certain number of
loadings of the aeroplane which the stopway is intended to serve
without inducing structural damage to the aeroplane.
3. Calculation of declared distances
3.1 The declared distances to be calculated for each
runway direction comprise: the take-off run available (TORA),
take-off distance available (TODA), accelerate-stop distance
available (ASDA), and landing distance available (LDA).
25/11/04 ATT A-2
Attachment A Annex 14 -Aerodromes
3.2 Where a runway is not provided with a stopway or
clearway and the threshold is located at the extremity of the
runway, the four declared distances should normally be equal
to the length of the runway, as shown in Figure A-1 (A).
3.3 Where a runway is provided with a clearway (CWY),
then the TODA will include the length of clearway, as shown
in Figure A-1 (B).
3.4 Where a runway is provided with a stopway (SWY),
then the ASDA will include the length of stopway, as shown
in Figure A-l (C).
3.5 Where a runway has a displaced threshold, then the
LDA will be reduced by the distance the threshold is displaced,
as shown in Figure A-1 (D). A displaced threshold
affects only the LDA for approaches made to that threshold;
all declared distances for operations in the reciprocal direction
are unaffected.
3.6 Figures A-l (B) through A-1 (D) illustrate a runway
provided with a clearway or a stopway or having a displaced
threshold. Where more than one of these features exist, then
more than one of the declared distances will be modified -
but the modification will follow the same principle illustrated.
An example showing a situation where all these features exist
is shown in Figure A-l (E).
3.7 A suggested format for providing information on
declared distances is given in Figure A-1 (F). If a runway direction
cannot be used for take-off or landing, or both, because
it is operationally forbidden, then this should be declared and
the words "not usable" or the abbreviation "NU" entered.
4. Slopes on a runway
4.1 Distance between slope changes
The following example illustrates how the distance between
slope changes is to be determined (see Figure A-2):
D for a runway where the code number is 3 should be at
least:
15 000 (Ix- yl + ly -21) m
IX - yl being the absolute numerical value of x - y
ly - zl being the absolute numerical value of y - z
Assuming x = + 0.01
y = -0.005
4.2 Consideration of longitudinal and
transverse slopes
When a runway is planned that will combine the extreme
values for the slopes and changes in slope permitted under
Chapter 3, 3.1.12 to 3.1 .I 8, a study should be made to ensure
that the resulting surface profile will not hamper the operation
of aeroplanes.
4.3 Radio altimeter operating area
In order to accommodate aeroplanes making auto-coupled
approaches and automatic landings (irrespective of weather
conditions) it is desirable that slope changes be avoided or
kept to a minimum, on a rectangular area at least 300 m long
before the threshold of a precision approach runway. The area
should be symmetrical about the extended centre line, 120 m
wide. When special circumstances so warrant, the width may
be reduced to no less than 60 m if an aeronautical study
indicates that such reduction would not affect the safety of
operations of aircraft. This is desirable because these
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：新建文件夾\附件14-機場 Aerodromes an14_v1_4ed(113)