(2)
Hydraulic-type installation with HARRISSON unions.
Titanium tube and union.
(Ref. Fig. 206/TASK 20-21-12-991-005)
R Tightening Torques for Clamps Figure 209/TASK 20-21-12-991-008
1EFF : 1 1 1CES ALL 1 111 20-21-12 Page 214 Aug 01/04
R Tightening Torques for Clamps Figure 210/TASK 20-21-12-991-009
1EFF : 1 1 1CES ALL 1 111 20-21-12 Page 215 Aug 01/04
TIGHTENING TORQUES FOR FLIGHT CONTROL THREADED FASTENERS
________________________________________________________ MAINTENANCE PRACTICES
_____________________
TASK 20-21-13-911-001
Tightening Torques for Flight Control Threaded Fasteners
1. Reason for the Job__________________
This subject gives the information related to the tightening torques for the standard threaded fasteners of the flight controls.
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-21-13-991-001 Fig. 201
3. Job Set-up
__________ Subtask 20-21-13-941-050
A. Not applicable.
4. Procedure
_________ Subtask 20-21-13-911-050
A. Tightening torques.
(Ref. Fig. 201/TASK 20-21-13-991-001)
(1) Tightening torques for the threaded fasteners of the flight controls.
Tightening Torques for the Threaded Fasteners of the Flight Controls
Figure 201/TASK 20-21-13-991-001
TIGHTENING TORQUES FOR OXYGEN UNIONS - MAINTENANCE PRACTICES
____________________________________________________________
TASK 20-21-14-911-001 Tightening Torques for Oxygen Unions
1. Reason for the Job
__________________
This subject gives the information related to the tightening torques for the the oxygen unions.
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
20-21-14-991-001 Fig. 201 20-21-14-991-002 Fig. 202 20-21-14-991-003 Fig. 203
3. Job Set-up
__________ Subtask 20-21-14-941-050
A. Not applicable
4. Procedure
_________ Subtask 20-21-14-911-050
A. Tightening Torques
(1)
Tightening torques for unions of all types, but not ANPT, used on steel tubes. (Ref. Fig. 201/TASK 20-21-14-991-001)
(2)
Tightening torques for unions of all types, but not ANPT, used on aluminum alloy tubes. (Ref. Fig. 202/TASK 20-21-14-991-002)
(3)
Tightening torques for ANPT unions used on aluminum alloy tubes. (Ref. Fig. 203/TASK 20-21-14-991-003)
Tightening Torques for Unions of all Types, but not ANPT, Used on Steel Tubes
Figure 201/TASK 20-21-14-991-001
Tightening Torques for Unions of all Types, but not ANPT, Used on Aluminum-alloy Tubes
Figure 202/TASK 20-21-14-991-002
Tightening Torques for ANPT Unions Used on Aluminum-alloy Tubes
Figure 203/TASK 20-21-14-991-003
TIGHTENING TORQUES FOR ELECTRICAL COMPONENT FASTENERS - MAINTENANCE PRACTICES
_____________________________________________________________________________
TASK 20-21-15-912-001
Tightening Torques for Electrical Component Fasteners
1. Reason for the Job
__________________
This subject gives the tightening torques for electrical component
fasteners.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STANDARD PRACTICES-AIRFRAME(14)
