3. Job Set-up
__________ Subtask 20-28-00-110-101
A. Removal of the Grease or Oil from the Contact Areas
(1) Remove any sign of grease or oil contamination with a MISCELLANEOUS (Material No. 19-003) moist with CLEANING AGENTS (Material No. 11-004).
4. Procedure
_________ Subtask 20-28-00-912-063
A. Antistatic Protection of the Surface of Non-Conductive Components (Kevlar or Glass Cloth). (Ref. Fig. 214/TASK 20-28-00-991-001, 215/TASK 20-28-00-991-034, 216/TASK 20-28-00-991-035, 217/TASK 20-28-00-991-036)
(1) Non-conductive components protected with antistatic paint.
(a) Get the electrical continuity of the external surface :
-directly with the antistatic paint below the fastener when this fastener is installed at the edge of the panel.
-with a bonding lead connected to the structure when the fastener is not installed at the edge of the panel. In all cases, put a conductive insert or washer between the antistatic paint and the fastener.
(2) Do a check of the electrical resistance (Ref. TASK 20-28-00-869-002). Subtask 20-28-00-912-064
B. Antistatic Protection of the Surface of Conductive Components.
(Ref. Fig. 218/TASK 20-28-00-991-002)
(1)
The fastener makes a path for the electrical continuity directly from the external surface to the structure.
(2)
Do a check of the electrical resistance (Ref. TASK 20-28-00-869-002).
5. Close-up
________ Subtask 20-28-00-942-108
A. Make sure that the work area is clean and clear of tool(s) and other items.
Bonding Principle of Non-Conductive Composite Components
Figure 214/TASK 20-28-00-991-001
Bonding of Removable Non-Conductive Composite Components
Figure 215/TASK 20-28-00-991-034
Edge Bonding of Non-Conductive Composite Panels
Figure 216/TASK 20-28-00-991-035
1EFF : ALL 1 20-28-00 Page 243
1 1 Feb 01/98
1 1
1CES 1
Bonding of Non-Conductive Composite Components
Figure 217/TASK 20-28-00-991-036
1EFF : ALL 1 20-28-00 Page 244
1 1 Feb 01/98
1 1
1CES 1
Bonding Principle of Conductive Composite Components
Figure 218/TASK 20-28-00-991-002
TASK 20-28-00-912-043
Electrical Bonding by Direct Contact
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS
_______
ONLY WITH A GOOD SUPPLY OF AIR.
OBEY THE MANUFACTURERS INSTRUCTIONS.
PUT ON PROTECTIVE CLOTHING.
DO NOT GET THEM IN YOUR MOUTH.
DO NOT SMOKE.
DO NOT BREATHE THE GAS.
THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific abrasive paper glass type 1
No specific grade 200 emery cloth
No specific lint free cloth
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-012 USA VV-P-236 PURE MINERALVASELINE OR PETRO- LATUM (Ref. 20-31-00)
R Material No. 09-016 USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)
Material No. 09-019 USA AMS 3267/3
LOW ADHESION CORROSION INHIBITING SEALANT
(Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STANDARD PRACTICES-AIRFRAME(90)
