_______

 (b)
 Put the O-ring (3) in position on the temperature sensor (2) and install the temperature sensor (2) in the duct (4).

 (c)
 TORQUE the temperature sensor (2) to between 0.5 and 0.525 m.daN

 (44.24 and 46.46 lbf.in) and safety with lockwire corrosion-resistant steel (0.30 in) dia.

 (d)
 Remove the blanking caps from the disconnected electrical connectors and connect the electrical connector (1).

 (e)
 Make sure that the work area is clean and clear of tool(s) and other items.

 THIS/THESE MATERIAL/S.
 USE PROTECTIVE CLOTHING, RUBBER GLOVES AND GOGGLES.
 1_ Make sure that the O-ring (3) is clean and in a good
 condition.
 2_ If necessary replace the O-ring (3).
 3_ Apply a small quantity of COMMON GREASE (Material No. 04-008)
 to the O-ring (3).
 4_ Remove the blanking plugs from the disconnected line ends.

R 1EFF : ALL 1 21-43-15Page 416 1 1 May 01/05 1 1 1CES 1

 (4) FOR 14HC
 (a)
 Preparation for Installation WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE

_______

 (b)
 Put the O-ring (7) in position on the temperature sensor (6) and install the temperature sensor (6) in the housing (8).

 (c)
 TORQUE the temperature sensor (6) to between 0.5 and 0.525 m.daN

 (44.24 and 46.46 lbf.in) and safety with lockwire corrosion-resistant steel (0.30 in) dia.

 (d)
 Remove the blanking caps from the disconnected electrical connectors and connect the electrical connector (5).

 (e)
 Make sure that the work area is clean and clear of tool(s) and other items.

 THIS/THESE MATERIAL/S.
 USE PROTECTIVE CLOTHING, RUBBER GLOVES AND GOGGLES.
 1_ Make sure that the O-ring (7) is clean and in a good
 condition.
 2_ If necessary replace the O-ring (7).
 3_ Apply a small quantity of COMMON GREASE (Material No. 04-008)
 to the O-ring (7).
 4_ Remove the blanking plugs from the disconnected line ends.

 Subtask 21-43-15-710-050
 B. Do the operational test of the pack temperature-control system (Ref. TASK 21-61-00-710-001).
 5. Close-up
________ Subtask 21-43-15-865-052
 A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 30HN, 31HN.
 1EFF : ALL 1 21-43-15Page 417 1 1 May 01/05R 1 1 1CES 1

R  **ON A/C 001-049, 051-099, 101-105, 201-213,
 Subtask 21-43-15-410-052
 B. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Install the access panel: 
R  (a) FOR 13HC - 151EW (Ref. TASK 25-55-11-400-003). 
R  (b) FOR 14HC - 151BC (Ref. TASK 25-55-11-400-002).
 (3) Remove the access platform(s).
 (4) Close the AFT cargo-compartment door 826 (Ref. TASK 52-30-00-860-002).
 (5) Remove the warning notice(s). 
R  **ON A/C 001-049, 051-099, 101-149, 201-299, 301-399, 
R  Post SB  21-1141 For A/C 001-049,051-099,101-105,201-213,
 Subtask 21-43-15-410-052-A
 B. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Install the access panel: 
R  (a) FOR 13HC - 151EW (Ref. TASK 25-55-11-400-003). 
R  (3) FOR 14HC - 161DW (Ref. TASK 25-55-11-400-003).
 (4) Remove the access platform(s).

 (5)
 Close the AFT cargo-compartment door 826 (Ref. TASK 52-30-00-860-002).

 (6)
 Remove the warning notice(s).

R  **ON A/C 151-199, 401-499, Post SB 21-1141 For A/C 151-199, Subtask 21-43-15-410-052-B
 B. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Install the access panel: R (a) FOR 13HC
 -151UW (Ref. TASK 25-55-11-400-003). R (3) FOR 14HC
 -161DW (Ref. TASK 25-55-11-400-003).
 (4)
 Remove the access platform(s).

 (5)
 Close the AFT cargo-compartment door 826 (Ref. TASK 52-30-00-860-002).

 (6) Remove the warning notice(s).
 **ON A/C ALL

 Subtask 21-43-15-862-050
 C. De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).

 CONTROLLER - HEAT (10HC) - REMOVAL/INSTALLATION_______________________________________________
 TASK 21-43-34-000-002
 Removal of the AFT Cargo Heat Controller (10HC)
 1. Reason for the Job__________________
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 3(76)