(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Install the rain repellent fluid gage assy (6) between the brackets.
(4)
Install the screws (2), (3), (10) and (11) with the washers (1), (4),
(12) and (13) and tighten them.
(5)
Remove the blanking plugs from the disconnected line ends.
(6)
Install a new o-ring (7) with the coupling (8).
(7)
Install the line (9).
(8)
Install a new seal (17).
(9)
Remove the protective cap from the drain valve (14).
(10)
Connect the hose to the drain valve (14) of the rain repellent fluid gage assy (6)
(11)
Put the hose outlet in the container.
R **ON A/C 001-049, 051-052, 054-099, 101-149, 151-199, 201-299, 301-399, R 401-499,
Post SB 30-1037 For A/C 001-049,051-052,054-056,
Subtask 30-45-43-420-052
A. Installation of the Rain Repellent Fluid Gage Assy
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Install the rain repellent fluid gage assy (6) between the brackets.
(4)
Install the screws (2), (3), (10) and (11) with the washers (1), (4),
(12) and (13) and tighten them.
(5)
Remove the blanking plugs from the disconnected line ends.
(6)
Install a new o-ring (7) with the coupling (8).
(7)
Install the line (9).
(8)
Install a new seal (17).
(9)
Put a new rain repellent fluid can (16) in position and tighten it manually.
NOTE : The assembly instructions are given on a caution plate near
____
the can and on the can.
(10)
Install the clamp (15) around the bracket assy and the can and tighten them.
(11)
Remove the protective cap from the drain valve (14).
(12)
Connect the hose to the drain valve (14) of the rain repellent fluid gage assy (6)
(13) Put the hose outlet in the container. **ON A/C ALL
Subtask 30-45-43-210-051
B. Inspection/Check
(1)
Push the pushbutton (5).
(2)
Make sure that the fluid level is correct and increases to the correct pressure.
(3) Make sure that there are no leaks. Subtask 30-45-43-942-051
C. Close-up operation
(1)
Disconnect the hose from the drain valve (14).
(2)
Install the protective cap on the drain valve (14).
1EFF : ALL 1 30-45-43Page 412 1 1 May 01/05R 1 1 1CES 1
Subtask 30-45-43-720-050
D. Do a functional test of the rain repellent system (Ref. TASK 30-45-00-720-002) ________
5. Close-up
Subtask 30-45-43-865-052
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1DB1, 1DB2
Subtask 30-45-43-410-051
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the warning notice(s).
(3) Close the access door of the rain repellent fluid gage assy (6). Subtask 30-45-43-862-050
C. De-energize the ground service network
(Ref. TASK 24-42-00-862-001)
1EFF : ALL 1 30-45-43Page 413 1 1 May 01/05R 1 1 1CES 1
NOZZLE - SPRAY - REMOVAL/INSTALLATION
_____________________________________
TASK 30-45-44-000-001 Removal of the Spray Nozzle WARNING : MAKE SURE THAT THE CIRCUIT BREAKERS RELATED TO THE WEATHER RADAR ARE
_______ OPENED, SAFETIED AND TAGGED.
1. Reason for the Job
__________________
NOTE : The removal/installation procedure of the spray nozzle is done from
____
out of the aircraft.
The spray nozzles are symmetrical but not interchangeable :
-
the CAPT spray nozzle is identified with red paint mark.
-
the F/O spray nozzle is identified with yellow paint mark. The procedure is the same for CAPT and F/O spray nozzles.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ICE AND RAIN PROTECTION 防冰和排雨2(35)
