F  『
 E  C F M  E
 E  E

 E E

 3. Job Set-up
__________
 Subtask 80-11-10-941-055

 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 80-11-10-010-057
 B. Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 4. Procedure
_________ R (Ref. Fig. 603/TASK 80-11-10-991-303) Subtask 80-11-10-210-055
 A. Inspect Starter for FOD.
 (1) Remove the V-clamp (70) which attaches the air supply duct (80) to the pneumatic starter (60) to get access to the starter, if necessary, remove the lower starter duct (Ref. TASK 80-13-42-000-041).

 (2) Introduces a mirror and a light in the starter exhaust, inspect the diffuser vane for any sign of FOD :

 - scratches, dents, missing segments.

 - signs, impacts.

 F 『 EEFF : ALL E Page 61480-11-10
 E E Nov 01/03 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (3) If any of the above signs is found:

 - remove and replace the starter (Ref. TASK 80-11-10-000-002) and (Ref. TASK 80-11-10-400-002).

 - Inspect the IP Bleed Check Valve (Ref. TASK 36-11-41-200-001) or (Ref. TASK 36-11-41-200-010), if this starter inspection is not applied per these tasks.

 (4) If you had removed the lower starter duct, install it (Ref. TASK 80-13-42-400-041).

 (5) If there is no sign of FOD, put the V-clamp (70) on the air supply duct (80) in position on the starter air inlet orifice. Lubricate the threads of clamp nut with graphite grease (Material No. CP2101). Install nut and TORQUE to between 70 and 80 lbf.in (0.79 and 0.90 m.daN) .

 5. Close-up
________
 Subtask 80-11-10-410-055
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (3) Remove the warning notice(s).

 F 『R EEFF : ALL E Page 61580-11-10
 E E Nov 01/03 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E

R  StarterInspection Figure 603/TASK 80-11-10-991-303- 12 (SHEET 1)
 F R EEFF : E E ECES  ALL  『 E 80-11-10EEE Page 616 Nov 01/03

R  StarterInspection Figure 603/TASK 80-11-10-991-303- 22 (SHEET 2)
 F EEFF : E E ECES  ALL  『E 80-11-10EEE Page 617 Nov 01/03

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 VALVE - STARTER SHUTOFF - REMOVAL/INSTALLATION

______________________________________________
 TASK 80-11-20-000-003
 Removal of the Starter Shutoff Valve
 1. Reason for the Job

__________________
 Self Explanatory

 2. Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific blanking caps
 No specific blanking plugs
 No specific soft-nose connector pliers
 No specific warning notice

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
 80-11-20-991-300 Fig. 401

 3. Job Set-up
__________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 80-11-20-941-053
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM 起動(dòng) STARTING(15)