**ON A/C ALL
 (4) Visual position indicator operation The manual override lever aligns with markings on the valve body to provide an external indication of butterfly position.
 F 『 EEFF : ALL E Page 1480-11-00
 E E Aug 01/05 E E ECES E F 『 E C F M E E E

 E 56-5B E

 Starter Shutoff Valve - Schematic Cross Section
 Figure 004A

 F 『R EEFF : 106-149, 155-199, 208-299, 301-399, E Page 1580-11-00
 E E401-499, Aug 01/05 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (5) Downstream facing probe The valve contains a downstream facing probe which prevents contaminants from entering the valve actuator and also requires no maintenance.

R **ON A/C 001-049, 051-099, 101-105, 151-154, 201-207,
 (6) Pneumatic heating operation The starter shutoff valve incorporates pneumatic solenoid heating to prevent icing of the solenoid valve. A small quantity of valve inlet air is routed through a flow control orifice, around the solenoid valve and then is vented to ambient.
 **ON A/C ALL
 (7) Position switch operation The normally open redundant electrical position switches are actuated by the closing end of the actuator to provide remote indication when the butterfly is in any position except closed.

 (8) Redundant solenoid The solenoid has two independent coils including 3 wires wound together (1 active winding per channel and 1 shunt winding to both active channels), either one of which when energized will open the valve.

 (9) Overpressure protection A relief valve is incorporated to limit the actuator pressure in the event that the inlet pressure exceeds the normal maximum value.

 F 『 EEFF : ALL E Page 1680-11-00
 E E May 01/05 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E E E PNEUMATIC STARTER AND VALVE SYSTEM - DEACTIVATION/REACTIVATION

______________________________________________________________
 TASK 80-11-00-040-044
 Check of the Starter Valve Manual Handle Position after Engine Start

 1. Reason for the Job
__________________
R Refer to the MMEL TASK: 80-11-04 R Pneumatic Starter and Valve System R Start Valve Position Indication on R ECAM Lower Display
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
80-11-00-991-300 Fig. 401
 3. Job Set-up
__________
 (Ref. Fig. 401/TASK 80-11-00-991-300)
 Subtask 80-11-00-010-050

 A. Open the access door on fan cowl :
 FOR 1000EM1
 438CR
 FOR 1000EM2
 448CR

 F 『 EEFF : ALL E Page 40180-11-00
 E E Nov 01/00 E E ECES E F 『 E C F M E E E E 56-5B E

 Starter Valve Access Panel
 Figure 401/TASK 80-11-00-991-300

 F 『 EEFF : ALL E Page 40280-11-00
 E E Feb 01/98 E E ECES E 4. Procedure

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

_________ Subtask 80-11-00-210-050
 A. After engine start cycle check on starter valve that the manual handle is in closed position.
 5. Close-up
________ Subtask 80-11-00-410-050
 A. Close the access door on fan cowl
 FOR 1000EM1
 438CR
 FOR 1000EM2
 448CR

 Subtask 80-11-00-941-050
 B. Safety Precautions
 (1) Install a warning notice in the cockpit to tell the persons that the starter valve 1 (2) indicating system is inoperative.

 (2) Make an entry in the log book.

 F 『 EEFF : ALL E Page 40380-11-00
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 80-11-00-040-045
R Manually Operate the Starter Valve
 1. Reason for the Job
__________________
 Refer to the MMEL TASK: 80-11-01
 Pneumatic Starter and Valve System
 Start Valve - Valve

 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 起動 STARTING(8)