(2) Install the new retaining ring (20) and retaining ring (20). PRE SB 74-002

 (3) Install the caged spring assembly (30) and caged spring assembly (30) to the ignition lead. Make sure that the large shoulder end of the caged spring assembly (30) is at the contact end of the ignition lead.

 (4) Install the new white chamfered silicone seal (10) to the ignition lead. The small diameter collar of the white chamfered silicone seal

 (10) must be put into the large collar of the caged spring assembly (30).
 POST SB 74-002
 (5) Install the new blue symmetrical silicone seal (10) to the ignition lead.
 END OF SB 74-002
 5. Close-up
________ Subtask 74-21-10-420-056
 A. Install the ignition lead (Ref. TASK 74-21-10-400-002).
 F 『 EEFF : ALL E Page 80974-21-10
 E E May 01/05 ERE
ECES E TASK 74-21-10-300-007 Repair of the Chafe Guard

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific lint-free cloth
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No.  CP1008 
R  Material No.  CP1039 
R 
Material No.  CP2011 
Material No.  CP2242 
R  Material No.  CP2559 
R 
R  Material No.  CP2560 
R 
R  Material No.  CP2566 
R 
R  Material No.  CP2584 
R 
R  Material No.  CP2656 
R 

*
 trichloroethylene (Ref. 70-30-00)
*
acetone (Ref. 70-30-00)
*
 stoddard solvent (Ref. 70-30-00)
USA MIL-A-46106A
 RTV 732 (Ref. 70-30-00)
*
ardrox 552 (Ref. 70-30-00)
*
turco ind 79 (Ref. 70-30-00)
*
mag-chem teksol (Ref. 70-30-00)
*
degreasol 99 R (Ref. 70-30-00)
*
mag-chem skysol (Ref. 70-30-00)

 F 『 EEFF : ALL E Page 81074-21-10
 E E May 01/05 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E
 C. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
74-21-10-000-002 Removal of the Right Ignition Lead
 74-21-10-400-002 Installation of the Right Ignition Lead
 74-21-10-991-305 Fig. 803

 3. Job Set-up
__________
 Subtask 74-21-10-020-057

 A. Remove the ignition lead (Ref. TASK 74-21-10-000-002).
 4. Procedure
_________
 (Ref. Fig. 803/TASK 74-21-10-991-305)
 Subtask 74-21-10-160-055

 A. Clean the Ignition Lead
 (1) Clean the damaged area of the ignition lead with a lint-free cloth R that is moist with trichloroethylene (Material No. CP1008) or R stoddard solvent (Material No. CP2011) or acetone (Material No. R CP1039) or ardrox 552 (Material No. CP2559) or turco ind 79 (Material R No. CP2560) or mag-chem teksol (Material No. CP2566) or degreasol 99R R (Material No. CP2584) or mag-chem skysol (Material No. CP2656) .
 (2) Let the surface air dry.
 Subtask 74-21-10-350-057

 B. Repair the Chafe Guard
 (1) Apply a thin layer of RTV 732 (Material No. CP2242) to the damaged area of the chafe guard.

 (2) Push the damaged chafe guard back into place.

 5. Close-up
________
 Subtask 74-21-10-420-057

 A. Install the ignition lead (Ref. TASK 74-21-10-400-002).
 F 『 EEFF : ALL E Page 81174-21-10
 E E May 01/05 E E ECES E F 『 E C F M E E E E 56-5B E

 Repair of the Chafe Guard
 Figure 803/TASK 74-21-10-991-305

 F 『 EEFF : ALL E Page 81274-21-10
 E E May 01/05 E E ECES E

 F  『
 E  C F M  E
 E  E

　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM IGNITION 點火(24)