F 『
 E C F M E
 E E
 E 56-5B E
 E E

 (3) Remove and discard the retaining ring (20).

 (4) Remove and discard the ceramic insulator sleeve (40).

 (5) Replace the ignition lead if the insulation has carbon tracks and arcing damage.

 POST SB 74-002

 (6) Remove and discard the blue symmetrical silicone seal (10).

 (7) Remove and discard the retaining ring (20).

 (8) Remove and discard the ceramic insulator (40).

 (9) Replace the ignition lead if the insulation has carbon tracks and arcing damage.

 END OF SB 74-002
 Subtask 74-21-20-160-054

 B. Clean all of the ignition lead components with a lint-free cloth that is R moist with trichloroethylene (Material No. CP1008) or stoddard solvent R (Material No. CP2011) or acetone (Material No. CP1039) or ardrox 552 R (Material No. CP2559) or turco ind 79 (Material No. CP2560) or mag-chem R teksol (Material No. CP2566) or degreasol 99 R (Material No. CP2584) or R mag-chem skysol (Material No. CP2656) .
 NOTE : The connector and all parts of the ignition lead must be clean.
____
 Subtask 74-21-20-350-056

 C. Assemble the Ignition Lead CAUTION : DO NOT APPLY GREASE OR ANY LUBRICANT TO THE THREADS OF THE
_______ CONNECTOR ON THE IGNITION LEAD. GREASE AND LUBRICANTS WILL CAUSE DAMAGE TO THE IGNITION LEAD AND THE SPARK IGNITER.
 (1) Install the new ceramic insulator sleeve (40) and ceramic insulator sleeve (40).

 (2) Install the new retaining ring (20) and retaining ring (20). PRE SB 74-002

 F 『R EEFF : ALL E Page 80874-21-20
 E E May 01/05 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (3) Install the caged spring assembly (30) and caged spring assembly (30) to the ignition lead. Make sure that the large shoulder end of the caged spring assembly (30) is at the contact end of the ignition lead.

 (4) Install the new white chamfered silicone seal (10) to the ignition lead. The small diameter collar of the white chamfered silicone seal

 (10) must be put into the large collar of the caged spring assembly (30).
 POST SB 74-002
 (5) Install the new blue symmetrical silicone seal (10) to the ignition lead.
 END OF SB 74-002
 5. Close-up
________ Subtask 74-21-20-420-056
 A. Install the ignition lead (Ref. TASK 74-21-20-400-002).
 F 『 EEFF : ALL E Page 80974-21-20
 E E May 01/05 ERE
ECES E TASK 74-21-20-300-006 Repair of the Chafe Guard

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific lint-free cloth
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No.  CP1008 
R  Material No.  CP1039 
R 
Material No.  CP2011 
Material No.  CP2242 
R  Material No.  CP2559 
R 
R  Material No.  CP2560 
R 
R  Material No.  CP2566 
R 
R  Material No.  CP2584 
R 
R  Material No.  CP2656 
R 

*
 trichloroethylene (Ref. 70-30-00)
*
acetone (Ref. 70-30-00)
*
 stoddard solvent (Ref. 70-30-00)
*
 RTV 732 (Ref. 70-30-00)
*
ardrox 552 (Ref. 70-30-00)
*
turco ind 79 (Ref. 70-30-00)
*
mag-chem teksol (Ref. 70-30-00)
*
degreasol 99 R (Ref. 70-30-00)
*
mag-chem skysol (Ref. 70-30-00)

 F 『 EEFF : ALL E Page 81074-21-20
 E E May 01/05 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E
 C. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM IGNITION 點火(33)