(c) Remove the 4 bolts (80) and disconnect the discharge hose (70) from the oil tank (30). Remove and keep the gasket (90).

 (d) Disconnect the drain tube (20) coupling nut from the oil scupper nipple.

 (e) Disconnect the hose (100) coupling nut from the tank nipple.

 (4) Disconnect the bonding strip (180) from the flange E as follows:

 (a) Remove the nut (210).

 (b) Remove the bolt (190) and the spacer (200).

 (5) Remove the oil tank (30) as follows: CAUTION : SUPPORT THE OIL TANK DURING THE REMOVAL OF THE

_______ SHOULDER-HEADED PIN TO PREVENT DAMAGE TO THE OIL TANK.
 F 『R EEFF : ALL E Page 40379-11-10
 E E May 01/01 E E ECES E F 『 E C F M E E E

 E 56-5B E

 Oil Tank Figure 401/TASK 79-11-10-991-302- 12 (SHEET 1)
 F 『R EEFF : 001-049, 051-061, 101-105, 151-151, E Page 40479-11-10
 E E201-203, May 01/05 E E ECES E F 『 E C F M E E E

 E 56-5B E

 Oil Tank Figure 401/TASK 79-11-10-991-302- 22 (SHEET 2)
 F 『R EEFF : 001-049, 051-061, 101-105, 151-151, E Page 40579-11-10
 E E201-203, May 01/05 E E ECES E F 『 E C F M E E E

 E 56-5B E

 Oil Tank
 Figure 401A/TASK 79-11-10-991-302-A12 (SHEET 1)

 F 『R EEFF : 062-099, 106-149, 152-199, 204-299, E Page 40679-11-10
 E E301-399, 401-499, Aug 01/05 E E ECES E F 『 E C F M E E E

 E 56-5B E

 Oil Tank
 Figure 401A/TASK 79-11-10-991-302-A22 (SHEET 2)

 F 『R EEFF : 062-099, 106-149, 152-199, 204-299, E Page 40779-11-10
 E E301-399, 401-499, Aug 01/05 E E ECES E E 56-5B E E E

 F  『
 E  C F M  E
 E  E

 (a) Remove the shoulder-headed pins (170) from the forward and aft lower mounts.

 (b) Remove and discard the cotter pin (220).

 (c) Remove the castellated nut (150) and the washer (140).

 (d) Remove the shoulder-headed pin (130).

 (e) Disengage the oil tank (30) from the lower mounts and remove it.

 (f) Remove dampers (160) from the brackets attached to flanges D/E and G.

 F 『 EEFF : ALL E Page 40879-11-10
 E E May 01/01 ERE
ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 79-11-10-400-005
 Installation of the Oil Tank
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
 No specific Torque Wrench : range 36.00 to 220.00 lbf.in

 (0.40 to 2.60 m.daN)
 No specific Torque Wrench : range 96.00 to 900.00 lbf.in

 (1.00 to 10.00 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP1039 *
 acetone (Ref. 70-30-00)
 Material No. CP1041 *
 isopropyl alcohol (Ref. 70-30-00)
 Material No. CP2010 *
 white spirit (Ref. 70-30-00)
 Material No. CP2011 *
 stoddard solvent (Ref. 70-30-00)
 Material No. CP2101 USA MIL-T-5544
 graphite grease (Ref. 70-30-00)
 Material No. CP2171 *
 molykote U-n (Ref. 70-30-00)
 Material No. CP2338 *
 Brisal-OX (Ref. 70-30-00)
 Material No. CP2442 *

 engine oil (Ref. 70-30-00) R Material No. CP2559 * R ardrox 552 (Ref. 70-30-00) R Material No. CP2560 *
 F 『 EEFF : ALL E Page 40979-11-10
 E E May 01/05 E E ECES E -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

turco ind 79 (Ref. 70-30-00)
 Material No. CP2566 *
 mag-chem teksol (Ref. 70-30-00)
 Material No. CP2584 *
 degreasol 99 R (Ref. 70-30-00)
 Material No. CP2656 *
 mag-chem skysol (Ref. 70-30-00)

 C. Expendable Parts
 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM OIL 滑油(25)