2. Operation

_________ (Ref. Fig. 001) The lubrication system consists of four subsystem, each of which accomplishes a specific function to ensure adequate lubrication for the bearings and gears of the engine :
 - the lube supply system

 - the lube scavenge system

 - the oil seal pressurization system

 - the sump venting system.

 NOTE : The appropriate lines and fittings are made of fire proof materials.
____
 3. Oil Servicing
_____________
 To permit servicing:

 - two drain ports are normally provided (a gearbox plug, a tank plug)

 - two filling ports on the oil tank (gravity and pressure).

 4. Component Location
__________________
 (Ref. Fig. 002, 003)

 -------------------------------------------------------------------------------FIN I FUNCTIONAL DESIGNATION I PANELIZONEIACCESS I ATA I I I I DOOR I REF. -------------------------------------------------------------------------------
4000EN  SW-LOW OIL PRESS 
4001EN  SW-OIL FILTER DIFF PRESS 
4002EN  XMTR-OIL QTY 
4003EN  XMTR-OIL PRESS 
4004EN  SENSOR-OIL TEMP 

435 437AL 79-34-15 445 447AL435 437AL 79-35-15 445 447AL435 437AL 79-31-15 445 447AL435 437AL 79-33-15 445 447AL435 437AL 79-32-15 445 447AL
  F 『 EEFF : ALL E Page 1 79-00-00 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Lube System Schematic
 Figure 001 (SHEET 1)

 F 『 EEFF : ALL E Page 279-00-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Lube System Schematic
 Figure 001 (SHEET 2)

 F 『 EEFF : ALL E Page 379-00-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Controls and Indicating - Component Location
 Figure 002
 F EEFF :  ALL  『E 79-00-00 Page 4 
E  E  Feb 01/98
 E  E
 ECES  E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 INTENTIONALLY BLANK

 F 『 E E Page 579-00-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Engine Lubrication System - Main Components Location Figure 003 (SHEET 1)
 F 『 EEFF : ALL E Page 679-00-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Engine Lubrication System - Main Components Location Figure 003 (SHEET 2)
 F 『 EEFF : ALL E Page 779-00-00
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E
 OIL - GENERAL - MAINTENANCE PRACTICES

_____________________________________
 TASK 79-00-00-480-001
 Installation of a Magnetic Bar in the Scavenge Screen Plugs (OPTIONAL)
 CAUTION : THE INSTALLATION OF THE MAGNETIC BARS IS ONLY AN HELP FOR
_______ TROUBLESHOOTING. REVENUE SERVICE FLIGHTS WITH THE MAGNETIC BARS INSTALLED MUST BE LIMITED TO 5 FLIGHTS OR 25 HOURS AND THEN THE MAGNETIC BARS MUST BE REMOVED.
 - IT IS TEMPORARY STEP FOR TROUBLESHOOTING AND MUST BE LIMITED TO ONE OF TWO ENGINES.
 1. Reason for the Job
__________________
 To identify the source of magnetic particles detected by the master chip detector, during a troubleshooting procedure.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice No specific Torque Wrench : range 36.00 to 220.00 lbf.in
 (0.40 to 2.60 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2442  * engine oil (Ref. 70-30-00)
 F 『 EEFF : ALL E Page 20179-00-00
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 C. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 79-21-10-000-007 Removal of the Scavenge Srceen Plugs from the
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM OIL 滑油(6)