(0.40 to 2.60 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2442 *
 engine oil (Ref. 70-30-00)
 Material No. CP8001 *
 lockwire 0.032 in. 0.8 mm dia. (Ref. 70-30-00)
 Material No. CP8002 *
 lockwire 0.032 in. 0.8 mm dia. (Ref. 70-30-00)

 C. Expendable Parts
 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R 20 O-ring 73-11-10 01B-160 R 20 O-ring 73-11-10 01C-160 R 30 O-ring 73-11-10 01B-160 R 30 O-ring 73-11-10 01C-160 R
 F 『 EEFF : ALL E Page 60173-11-10
 E E Aug 01/03 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 D. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-00-00-710-006 Minimum Idle Check 71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 72-63-00-000-002 Removal of the Handcranking Drive Cover 72-63-00-400-002 Installation of the Handcranking Drive Cover 73-11-10-000-003 Removal of the Fuel Pump and Filter Assembly 73-11-10-400-003 Installation of the Fuel Pump and Filter Assembly 78-30-00-081-041 Make the Thrust Reverser Serviceable after
 Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
 Maintenance 78-36-00-010-040 Opening of the Thrust Reverser Doors 78-36-00-410-040 Closing of the Thrust Reverser Doors 73-11-10-991-303 Fig. 601
 3. Job Set-up
__________
 Subtask 73-11-10-941-057
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 F 『 EEFF : ALL E Page 60273-11-10
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 Subtask 73-11-10-010-063

 B. Get Access
 (1) Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 Subtask 73-11-10-040-052
 C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
 Subtask 73-11-10-010-064
 D. Open the thrust reverser doors: (Ref. TASK 78-36-00-010-040)
 FOR 1000EM1
 451AL, 452AR
 FOR 1000EM2
 461AL, 462AR

 4. Procedure
_________
 (Ref. Fig. 601/TASK 73-11-10-991-303)
 Subtask 73-11-10-210-052
 A. Inspection of the Impeller Rotation
 (1) Remove the cover from the handcranking drive pad (Ref. TASK 72-63-00-000-002)

 (2) Engage a 3/4 in. square drive adapter, fitted with shear neck, in the handcranking drive shaft.

 (3) Remove inspection plug (10) (lube flow screen) from the fuel pump as follows:

 (a) Cut and remove lockwire.

 (b) Remove plug (10) from pump cover assembly.

 (c) Remove and discard preformed packings (20 and 30) from plug (10).

 (4) Manually turn the handcranking drive shaft.

 F 『 EEFF : ALL E Page 60373-11-10
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Check of Impeller Rotation
 Figure 601/TASK 73-11-10-991-303

 F 『 EEFF : ALL E Page 60473-11-10
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (5) Through plug (10) orifice, check that LP pump impeller turns correctly.

 (a) If so, reinstall the removed parts.

 (b) If not, replace the pump (Ref. TASK 73-11-10-000-003) and (Ref. TASK 73-11-10-400-003).

 (6) Install the handcrancking drive pad cover (Ref. TASK 72-63-00-400-002). the cover.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 發動機燃油和控制 ENGINE FUEL AND CONTRO(35)