3. Job Set-up
__________
 Subtask 72-23-00-941-085

 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 72-23-00-010-108
 B. Get Access
 (1) Open the fan cowl doors: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR

 (2) Put the access platform in position.

 4. Procedure
_________ R (Ref. Fig. 608/TASK 72-23-00-991-321) Subtask 72-23-00-210-063
 A. Visual Inspection of the PS12 Line CAUTION : USE 2 WRENCHES TO REMOVE/INSTALL THE TUBE UNION NUT: ONE TO
_______ HOLD THE FITTING, THE OTHER TO LOOSE/TORQUE THE NUT. OTHERWISE, DAMAGE TO THE HARDWARE CAN OCCUR.
 F 『 EEFF : ALL E Page 64272-23-00
 E E May 01/05 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 INTENTIONALLY BLANK

 F 『R E E Page 64372-23-00
 E E Aug 01/05 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E

R  PS12 Line Figure 608/TASK 72-23-00-991-321- 14 (SHEET 1)
 F EEFF : E E ECES  ALL  『E 72-23-00EEE Page 644 May 01/05

R  PS12 Line Figure 608/TASK 72-23-00-991-321- 24 (SHEET 2)
 F EEFF : E E ECES  ALL  『E 72-23-00EEE Page 645 May 01/05

R  PS12 Line Figure 608/TASK 72-23-00-991-321- 34 (SHEET 3)
 F EEFF : E E ECES  ALL  『E 72-23-00EEE Page 646 May 01/05

R  PS12 Line Figure 608/TASK 72-23-00-991-321- 44 (SHEET 4)
 F EEFF : E E ECES  ALL  『E 72-23-00EEE Page 647 May 01/05

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (1) Inspect the PS12 line as follows:

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Inspect the hose for:
 - broken hose braid  3 broken wires per
 plait, and no more than
 6 broken wires per
 assembly, or per lineal
 12 in. (305 mm) of hose.

 - crimps  Not serviceable Replace the PS12 line (Ref. TASK 72-23-00-000-040) and (Ref. TASK 72-23-00-400-040).

 Subtask 72-23-00-210-061
 B. Visual Inspection of the PS12 Line
 CAUTION : USE 2 WRENCHES TO REMOVE/INSTALL THE TUBE UNION NUT: ONE TO
_______ HOLD THE FITTING, THE OTHER TO LOOSE/TORQUE THE NUT. OTHERWISE, DAMAGE TO THE HARDWARE CAN OCCUR.
 (1) Inspect the PS12 hose connections as follows:
 (a) Cut and remove the lockwires.

 (b) Disconnect the PS12 hose from the ECU and from the fan frame bosses.

 F 『 EEFF : ALL E Page 64872-23-00
 E E Aug 01/05 ERE
ECES  E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (c) Inspect the connections as follows:

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Fitting nuts for:
 - damaged corners  Any amount, provided
 proper torque can be
 obtained.

 - damaged threads  Any amount, provided Chase the threads.
 effective threads are
 not reduced by more than
 one after chasing.

 - safetywire hole  Serviceable, provided
 deformation and metal around hole is not
 wear. cracked or torn.

 2. Fittings seating surfaces for:
 - circumferential  Any amount not

 scratches  detectable with a 0.04
 in. (1 mm) radius ball
 scribe.

 - axial scratches  Not serviceable Replace the hose or the part.

 - nicks, pits  Not serviceable Replace the hose or the part.

 (2) Clean the weep holes with white spirit (Material No. CP2010) and plastic wire.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 2