曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  PRONER BNC4 hand crimping tool (P/N S111001129070) is used for crimping 
R  open-barrel connecting elements (e.g. E0256) comprising crimping legs. 
R  Crimping chamber change
R  ____NOTE : : After any crimping chamber change, operate tool at no load to 
R  ensure correct operation then tighten knurled nut while squeezing 
R  tool handles. 
R  On barrel : 
R  - loosen knurled nut. 
R  - open tool. 
R  - turn barrel to select correct crimping chamber. 
R  On indenter :
R  ____NOTE : : Loosen indenter screw. 
R  - open tool. 
R  - remove indenter. 
R  - turn or change indenter, ensuring correct orientation in slot. 
R  - tighten screw.
R  ____NOTE : : Three interchangeable indenters, each having 2 indentations, are 
R  available.

 

 Hand Crimping Tool-PRONER BNC4 P/N S111001129070 R Figure 025

20-25-22 Page 5320-25-22 Page 54

R  ___________________________________23. AMP Hand Crimping Tool P/N 753898-1 
R  (Ref. Fig. 026) 
R  Example of connection P/N used with this tool 
R  ---------------------------------------------------------------
R  | CRIMPING TOOLS | CONNECTION | 
R  |--------------------------|-----------------------------------| 
R  | NORM | P/N | P/N | TYPE | 
R  |------------|-------------|---------------|-------------------| 
R  | AMP | 753898-1 | ABS0374 | TERMINALS | 
R  ----------------------------------------------------------------
R  The tools have a ratchet system assuring full crimping before opening of 
R  jaws. 
R  Periodic check shall be guaranteed by an inspection stamp.
R  ______________________________________24. DANIELS Hand Crimping Tool P/N GMT 221 
R  (Ref. Fig. 027) 
R  Example of connection P/N used with this tool 
R  ----------------------------------------------------------------
R  | CRIMPING TOOLS | CONNECTION | 
R  |--------------------------|-----------------------------------| 
R  | NORM | P/N | P/N | TYPE | 
R  |------------|-------------|---------------|-------------------| 
R  | DANIELS | GMT 221 | E0367 | NORMAL CONTACTS | 
R  ----------------------------------------------------------------

 

 Hand Crimping Tool-AMP P/N 753898-1 R Figure 026

20-25-22 Page 55

 Hand Crimping Tool-DANIELS P/N GMT 221 R Figure 027

20-25-22 Page 5620-25-22 Page 57

R  _______________________________________25. SOURIAU Hand Crimping Tool P/N CCT 1612 
R  (Ref. Fig. 028) 
R  Example of connection P/N used with this tool 
R  ----------------------------------------------------------------
R  | CRIMPING TOOLS | CONNECTION | 
R  |--------------------------|-----------------------------------| 
R  | NORM | P/N | P/N | TYPE | 
R  |------------|-------------|---------------|-------------------| 
R  | SOURIAU | CCT 1612 | NSA938192 | NORMAL CONTACTS | 
R  ----------------------------------------------------------------
R  This tool must be fitted with a locator corresponding to the contact to be 
R  crimped. 
R  The locator is attached to the tool by means of a latch. 
R  Tool CCT 1612 is fitted with a 2-position stop, one for gauge 16 contacts, 
R  the other for gauge 12 contacts. 
R  A GO-NO GO gauge is used to check condition of crimping tool.
R  ___________________________________26. DANIELS Hand Crimping Tool P/N M309 
R  (Ref. Fig. 029) 
R  Example of connection P/N used with this tool 
R  ----------------------------------------------------------------
R  | CRIMPING TOOLS | CONNECTION | 
R  |--------------------------|-----------------------------------| 
R  | NORM | P/N | P/N | TYPE | 
R  |------------|-------------|---------------|-------------------| 
R  | DANIELS | M309 | ABS0715 | NORMAL CONTACTS | 
R  ----------------------------------------------------------------
R  The tool is designed to crimp 18 to 12 gauge wires and incorporates a 
R  selector knob numbered from 1 to 8 to ajust the crimp depth. 
R  Crimping is obtained by means of a turret head assembly or positioner which 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 1(101)