- diconnect the electrical connector from the DEU TERMINATION BOX (309RH2) (Ref. ASM 23-73/06),
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 106-149, 401-499, ∞∞23-73-00∞∞∞∞∞∞∞∞∞∞Page A278
Aug 01/05 CES - do a check for a short circuit again.
1 If there is a short circuit:
_
- reconnect the electrical connector to the DEU TERMINATION BOX (309RH2)
- do the steps 4. B. (7) again for the subsequent DEU(s) and DEU CONNECTION BOX(es) until the maintenance message stops: (Ref. ASM 23-73/06) DEU-B (300RH6) and DEU CONNECTION BOX (308RH6), DEU CONNECTION BOX (308RH2),
2 If there is no short circuit:
_
- do a check for a short circuit at the disconnected connector between the pins A/9 and A/10 (Ref. ASM 23-73/06)
a If there is a short circuit:
_
- repaire the wiring between the related DEU CONNECTION BOX 308RHxx and the DEU CONNECTION/ TERMINATION BOX 308RHxx/309RHxx (Ref. ASM 23-73/06).
b If there is no short circuit:
_
- install a new DEU TERMINATION BOX (309RH2) ((Ref. AMM 23-73-43-400-00100)).
**ON A/C 151-199,
B. If the CIDS1/CIDS BUS test gives the maintenance message CIDS MID BUS R:
- make sure that at least one cabin door is open,
- remove the DIR-CIDS (101RH) (Ref. AMM TASK 23-73-34-000-001),
- close these CBs:
49VU: 157RH (G02) CIDS/DIR 2/ESS,
121VU:156RH (M07) CIDS/DIR 2/NORM,
- wait for approx. 120 s,
- do the CIDS2/CIDS BUS test through the CFDS/MCDU.
(1) If the CIDS2/CIDS BUS test is OK:
- install a new DIR-CIDS, 1 (101RH) (Ref. AMM TASK 23-73-34-400-001).
(2) If the fault continues:
- remove the DIR-CIDS, 2 (102RH) (Ref. AMM TASK 23-73-34-000-001).
- during the installation of the DIR-CIDS, 1 (101RH) do not close these CBs: 49VU: 157RH (G02) CIDS/DIR 2/ESS, 121VU:156RH (M07) CIDS/DIR 2/NORM,
- install the DIR-CIDS, 1 (101RH) (Ref. AMM TASK 23-73-34-400-001).
- do the CIDS1/CIDS BUS test through the CFDS/MCDU.
(3) If the CIDS1/CIDS BUS test is OK:
- install a new DIR-CIDS, 2 (102RH) (Ref. AMM TASK 23-73-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 106-149, 151-199, 401-499, ∞∞23-73-00∞∞∞∞∞∞∞∞∞∞Page A279
Aug 01/05 CES
(4) If the fault continues:
- remove the DIR-CIDS, 1 (101RH) (Ref. AMM TASK 23-73-34-000-001)
- open these CBs:
49VU: 153RH COM/CIDS/DEU B/ESS
120VU: 162RH COM NAV/CIDS/DEU B/NORM
- make sure that the resistance (line to line) at DIR-CIDS (101RH) and (102RH) connector AA/A14 and connector AA/B14 is between approx. 80 and 200 ohms (Ref. ASM 23-73/06).
(5) If the resistance (line to line) is between approx. 80 and 200 ohms:
- make sure that the resistance (line to GND) is not less than 50 ohms (short circuit) between: DIR-CIDS (101RH) and (102RH) connector AA/A14 and GND, DIR-CIDS (101RH) and (102RH) connector AA/B14 and GND. (Ref. ASM 23-73/06)
(a) If there is no short circuit:
- remove the DEU-B (300RH6) (Ref. AMM TASK 23-73-47-000-001)
- install the DIR-CIDS (101RH) and DIR-CIDS (102RH) (Ref. AMM TASK 23-73-34-400-001).
- close these CBs: 49VU: 153RH COM/CIDS/DEU B/ESS 120VU: 162RH COM NAV/CIDS/DEU B/NORM
- do the CIDS BITE test through the CFDS/MCDU (Ref. AMM TASK 23-73-00-740-005).
1 If the CIDS BITE test gives the maintenance message DEU-B
_
300RH6:
- install a new DEU-B (300RH6) (Ref. AMM TASK 23-73-47-400-001).
2 If the CIDS BITE test gives the maintenance message CIDS MID
_
BUS R:
- install the removed DEU-B (300RH6) (Ref. AMM TASK 23-73-47-400-001).
- do the steps 4. B. (5) (a) again for the subsequent DEU(s) until the maintenance message stops: (Ref. ASM 23-73/06) DEU-B (300RH4)
(b) If there is a short circuit:
- remove the DEU-B (300RH6) (Ref. AMM TASK 23-73-47-000-001),
- do a check for a short circuit again.
1 If there is no short circuit:
_
- install a new DEU-B (300RH6) (Ref. AMM TASK 23-73-47-400-001).
2 If the fault continues:
_
- disconnect the electrical connector 7247VC2 from the DEU mount 2015VU2 (Ref. AMM TASK 23-73-48-000-001).
- do a check for a short circuit again. 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 COMMUNICATIONS 通訊2(109)
