R A. Remove the hubcap or the debris guard (if brake fans are installed) (Ref.
R AMM TASK 32-41-11-000-006).
R (1) Do a visual inspection of the tachometer drive mechanism and make
R sure that:
R - the tachometer drive shaft moves freely.
R - there is no deformation (twisting) and/or sign of friction on the
R drive shaft.
R - the splines of the tachometer drive shaft are in the correct
R condition.
R - the splines of the tachometer hubcap or the splines of the debris
R guard (if brake fans are installed) are in the correct condition.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-42-00∞∞∞∞∞∞∞∞∞∞Page 235
May 01/05 CES
R (2) If the tachometer drive is damaged:
R - replace the DRIVE ASSY-TACHOMETER,WHEEL 3 (2679GM) (Ref. AMM TASK
R 32-42-68-000-003) and (Ref. AMM TASK 32-42-68-400-003).
R (3) If the tachometer hubcap or the debris guard (if brake fans are
R installed) is damaged:
R - replace the tachometer hubcap or the debris guard (if brake fans
R are installed) (Ref. AMM TASK 32-41-11-000-006).
R (4) If the tachometer drive mechanism is not damaged:
R - do a functional test of the tachometer (Ref. AMM TASK 32-42-00-720-
R 002) or (Ref. AMM TASK 32-42-00-720-003).
R (a) if the test is OK:
R - Make sure that the splines of the tachometer are coated with
R grease before final assembly (Ref. AMM TASK 32-41-11-400-006).
R No other maintenance action is necessary.
R (b) if the test confirms the fault:
R - replace the TACHOMETER-WHEEL 3 (20GG) (Ref. AMM TASK 32-42-57-
R 000-001) (Ref. AMM TASK 32-42-57-400-001)
R (5) If the fault continues:
R - do the trouble shooting procedure (Ref. TASK 31-32-00-810-933)
R related to the ANI-6 analog input signal of the SEC 2 COM and SEC 3
R COM (Ref. ASM 27-92/25).
R (6) If the fault continues:
R - do a check and repair the wiring from the tachometer (20GG) pins
R A/A,C to the first terminal block (Ref. ASM 32-42/02).
R B. Do the functional test given in Para. 4.A.(4)
TASK 32-42-00-810-823
Loss of the Signal from the Green Pressure Switch
1. Possible Causes
_______________
- PRESS SW-FLT CTL, G (1151GN)
- BSCU (10GG)
- wiring from the pressure switch (1151GN) to the BSCU (10GG)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 29-32-12-000-001 Removal of the System Pressure Switch (1151GN) AMM 29-32-12-400-001 Installation of the System Pressure Switch (1151GN) AMM 32-42-34-000-001 Removal of the Braking/Steering Control Unit (BSCU)
(10GG) AMM 32-42-34-400-001 Installation of the Braking/Steering Control Unit (BSCU) (10GG) ASM 32-42/03
3. Fault Confirmation
__________________
A. Test
Not applicable
4. Fault Isolation
_______________
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220, 301-399,
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 起落架 LANDING GEAR 1(108)
