- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
1. Possible Causes
_______________
R - UPLOCK ASSY-MLG, R (2510GM) R - proximity sensors and targets R - grease contamination of the uplock proximity sensors and targets
- MLG (RH) lockstay assembly
- MLG (RH) uplocks
- ACTG CYL-MLG R (2504GM)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 32-31-00-810-846 L/G Failure of one of the uplock proximity sensors
R 8GA thru 13GA AMM 32-11-00-200-001 Inspection/Check of the Main Gear AMM 32-11-00-220-003 Detailed Dimensional Check of the MLG Lockstay
Assembly AMM 32-31-00-200-001 Detailed Inspection of Gear Uplock and Door Uplock Units and Pins AMM 32-31-00-720-002 Functional Test of the Normal Extension and
Retraction of the Landing Gear
AMM 32-31-46-000-001 Removal of the MLG Actuating Cylinder
AMM 32-31-46-400-001 Installation of the MLG Actuating Cylinder
R
3. Fault Confirmation
__________________
A. Procedure
(1) Do a check of the post flight report. If there is a SYS DISAGREE ECAM message and related MLG (RH) uplock target-position CFDS message, do the Fault Isolation procedure
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-31-00∞∞∞∞∞∞∞∞∞∞Page A247
Aug 01/05 CES
4. Fault Isolation
_______________
A. Procedure NOTE : The procedure that follows, gives the information necessary to
____ identify mechanical faults related to the MLG (RH).
(1) Do the inspection/check of the main gear (RH) (Ref. AMM TASK 32-11-00-200-001).
R (2) Do a check of the UPLOCK ASSY-MLG, R (2510GM) proximity sensors and R targets (Ref. TASK 32-31-00-810-846).
R (a) If the indications are not correct during the check, do the R following:
R 1_ Do a check for grease contamination of the uplock proximityR sensors and targets.
R 2_ If there is too much grease in the area, clean off the greaseR and do the check in Para. 4.A. again.
R NOTE : Grease contamination can cause incorrect indications.
____ R
(3) Do the detailed dimensional check of the MLG (RH) lockstay assembly (Ref. AMM TASK 32-11-00-220-003).
(4) Do the detailed inspection of the MLG (RH) uplocks (Ref. AMM TASK 32-31-00-200-001).
R (5) Correct all faults found.
(6) Do the functional test of the normal extension and retraction of the landing gear (Ref. AMM TASK 32-31-00-720-002).
(7) If the fault continues, the MLG (RH) is slow to operate or the fault continues after the subsequent flight, replace the ACTG CYL-MLG R (2504GM) (Ref. AMM TASK 32-31-46-000-001) (Ref. AMM TASK 32-31-46-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-31-00∞∞∞∞∞∞∞∞∞∞Page A248
Aug 01/05 CES
TASK 32-31-00-810-868
NLG Shock Absorber Does Not Extend
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
1. Possible Causes
_______________
- NLG proximity sensor and target clearances
- NLG torque link assembly
- charge pressure of the nose landing gear (NLG) shock absorber
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 12-12-32-611-005 Replenishment of the NLG Shock Absorber (Aircraft on
Jacks) AMM 12-14-32-614-004 Check Shock Absorber Charge Pressure AMM 32-21-00-200-002 General Visual Inspection of the Nose Landing Gear AMM 32-21-00-200-003 Check Torque Links for Excessive Play AMM 32-31-00-720-003 Functional Test of the Normal Extension and
Retraction of the Nose Landing Gear AMM 32-31-73-200-002 Inspection of the NLG Proximity Sensor and Target Clearances
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 起落架 LANDING GEAR 1(58)
