- replace the SPEED SENSOR (8060KM2) (Ref. AMM TASK 49-71-13-000-001) and (Ref. AMM TASK 49-71-13-400-001). and
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-001) and (Ref. AMM TASK 49-61-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-003, 051-099, 401-499, ∞∞49-00-00∞∞∞∞∞∞∞∞∞∞Page 232
Config-1 Aug 01/05 CES
B. Do the test given in para. 3.
NOTE : It is recommended to make an entry in the applicable logbook that
____ you must read the APU CLASS 3 FAULTS after the first flight on the subsequent day. If the APU CLASS 3 FAULTS page gives the maintenance message SPEED SENSOR (8060KM2) after the first flight on the subsequent day:
- do the applicable trouble shooting procedure (Ref. TASK 49-70-00-810-802).
R **ON A/C 001-003, 051-099, 401-499,
TASK 49-00-00-810-812
APU AUTO SHUT DOWN - SENSOR FAILURE (GTCP 36-300)
1. Possible Causes
_______________
- EGT THERMOCOUPLE RAKE 1
- EGT THERMOCOUPLE RAKE 2
- wiring
- ECB (59KD)
- EGT THERMOCOUPLE RAKE (8057KM1)
- EGT THERMOCOUPLE RAKE (8057KM2)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
49-70-00-810-803 Thermocouple Rake 1 Defective (GTCP 36-300) 49-70-00-810-804 Thermocouple Rake 2 Defective (GTCP 36-300) AMM 49-00-00-710-004 Operational Test of the APU (4005KM) (GTCP 36-300) AMM 49-61-34-000-001 Removal of the Electronic Control Box (ECB) (59KD)
(GTCP 36-300) AMM 49-61-34-400-001 Installation of the Electronic Control Box (ECB) (59KD) (GTCP 36-300) AMM 49-72-15-000-001 Removal of the Thermocouple (8057KM1) and (8057KM2) (APS 3200) AMM 49-72-15-000-003 Removal of the Thermocouple Probes (8057KM1) and (8057KM2) (GTCP 36-300) AMM 49-72-15-400-001 Installation of the Thermocouple Probes (8057KM1) and (8057KM2) (GTCP 36-300) ASM 49-61/02
3. Fault Confirmation
__________________
A. Do the operational test of the APU (Ref. AMM TASK 49-00-00-710-004).
4. Fault Isolation
_______________
**ON A/C 001-003, 051-062,
A. If an APU auto shutdown occurs during the operational test of the APU and the APU SHUTDOWNS report gives the maintenance message:
SENSOR FAILURE - BOTH EGT TC RAKES:
- replace the EGT THERMOCOUPLE RAKE 1 and the EGT THERMOCOUPLE RAKE 2 (Ref. AMM TASK 49-72-15-000-001) and (Ref. AMM TASK 49-72-15-400-001).
(1) If the fault continues:
- do a check and repair the wiring from the ECB (59KD) AB/A6, A7 to the EGT THERMOCOUPLE RAKE 1 studs/alumel, chromel (Ref. ASM 49-61/02).
- do a check and repair the wiring from the ECB (59KD) AB/A8, A9 to the EGT THERMOCOUPLE RAKE 2 studs/alumel, chromel (Ref. ASM 49-61/02).
(2) If the fault continues:
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-001) and (Ref. AMM TASK 49-61-34-400-001).
B. Do the test given in para. 3.
NOTE : It is recommended to make an entry in the applicable logbook that
____ you must read the APU CLASS 3 FAULTS after the first following flight. If the APU CLASS 3 FAULTS page gives the maintenance message EGT TC RAKE 1 after the first following flight:
- do the applicable trouble shooting procedure (Ref. TASK 49-70-00-810-803). If the APU CLASS 3 FAULTS page gives the maintenance message EGT TC RAKE 2 after the first following flight:
- do the applicable trouble shooting procedure (Ref. TASK 49-70-00-810-804).
R **ON A/C 063-099, 401-499,
A. If an APU auto shutdown occurs during the operational test of the APU and the APU SHUTDOWNS report gives the maintenance message:
SENSOR FAILURE - EGT TCPLE RAKES (8057KM1) AND (8057KM2)
with the LRU TROUBLE SHOOT DATA menu information:
BOTH EGT SENSORS FAILED
Fault Code Number: 035
- replace the EGT THERMOCOUPLE RAKE (8057KM1) and the EGT THERMOCOUPLE RAKE (8057KM2) (Ref. AMM TASK 49-72-15-000-003) and (Ref. AMM TASK 49-72-15-400-001). 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 機載輔助動力 1(12)
