1 If the oil pump output-shaft turns constantly (the oil pump
_
input-shaft is not broken):
- install a new FUEL CONTROL UNIT (8022KM) (Ref. AMM TASK 49-32-11-400-001).
(b) If the fault continues:
- replace the FLOW DIVIDER AND DRAIN VALVE ASSY (8024KM) (Ref. AMM TASK 49-32-12-000-001) and (Ref. AMM TASK 49-32-12-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 063-099, 401-499, ∞∞49-00-00∞∞∞∞∞∞∞∞∞∞Page 266
Config-1 Aug 01/05 CES
(c) If the fault continues:
- replace the PRIMARY FUEL NOZZLE AND MANIFOLD (8020KM) (Ref. AMM TASK 49-31-41-000-001) and (Ref. AMM TASK 49-31-41-400-001).
- replace the SECONDARY FUEL NOZZLE AND MANIFOLD (8021KM) (Ref. AMM TASK 49-31-41-000-001) and (Ref. AMM TASK 49-31-41-400-001).
(d) If the fault continues:
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-001) and (Ref. AMM TASK 49-61-34-400-001).
R **ON A/C 001-003, 051-099, 401-499,
B. Do the operational test of the APU (Ref. AMM TASK 49-00-00-710-004).
TASK 49-00-00-810-822
APU AUTO SHUT DOWN - REVERSE FLOW, Differential Pressure Transducer P24 -, or
Total Pressure Transducer P23 -, or Surge Ctl Valve - Fault (GTCP 36-300)
1. Possible Causes
_______________
- ECB (59KD)
- PNEUMAIC-SENSOR-ASSY
- SURGE CONTROL VALVE P18
- LOAD-COMPRESSOR INLET-TEMPERATURE SENSOR P22
- wiring
- PNEUMAIC-SENSOR-ASSY (8039KM)
- SURGE CONTROL VALVE (8058KM)
- LOAD-COMPRESSOR INLET-TEMPERATURE SENSOR (8011KM)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 49-00-00-710-004 Operational Test of the APU (4005KM) (GTCP 36-300) AMM 49-23-15-000-001 Removal of the Load-Compressor Inlet Temperature-Sensor (8011KM) ((GTCP 36-300)) AMM 49-23-15-400-001 Installation of the Load-Compressor Inlet
Temperature-Sensor (8011KM) ((GTCP 36-300)) AMM 49-51-13-000-001 Removal of the Pneumatic Sensor Assy (GTCP 36-300) AMM 49-51-13-400-001 Installation of the Pneumatic Sensor Assy (GTCP
36-300) AMM 49-51-52-000-002 Removal of the Surge Control Valve (8058KM) (GTCP 36-300) AMM 49-51-52-400-002 Installation of the Surge Control Valve (8058KM) (GTCP 36-300) AMM 49-61-34-000-001 Removal of the Electronic Control Box (ECB) (59KD) (GTCP 36-300) AMM 49-61-34-400-001 Installation of the Electronic Control Box (ECB) (59KD) (GTCP 36-300) ASM 49-61/02
3. Fault Confirmation
__________________
A. Do the operational test of the APU (Ref. AMM TASK 49-00-00-710-004).
4. Fault Isolation
_______________
**ON A/C 001-003, 051-062,
A. If an APU auto shutdown occurs and the APU SHUTDOWNS report gives the maintenance message:
REVERSE FLOW - DP XDCR P24 OR PT XDCR P23 OR SCV:
NOTE : If an APU auto shutdown occurs with the Bleed Ctl Valve closed (NO
____ BLEED Demand) then start with step (2) (LCIT P22 Replacement).
- replace the PNEUMAIC-SENSOR-ASSY
(Ref. AMM TASK 49-51-13-000-001)
(Ref. AMM TASK 49-51-13-400-001).
(1) If the fault continues:
- replace the SURGE CONTROL VALVE P18
(Ref. AMM TASK 49-51-52-000-002)
(Ref. AMM TASK 49-51-52-400-002).
(a) If the fault continues:
- replace the LOAD-COMPRESSOR INLET-TEMPERATURE SENSOR P22
(Ref. AMM TASK 49-23-15-000-001) (Ref. AMM TASK 49-23-15-400-001).
(b) If the fault continues:
- do a check and repair the wiring from the ECB (59KD) AB/E6, E7 to the LOAD-COMPRESSOR INLET-TEMPERATURE SENSOR P22 studs/alumel, chromel (Ref. ASM 49-61/02).
(c) If the fault continues:
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-001)
(Ref. AMM TASK 49-61-34-400-001). R **ON A/C 063-099, 401-499,
A. If an APU auto shutdown occurs and the APU SHUTDOWNS report gives the maintenance message:
REVERSE FLOW - PRESS XDCRS (8048KM)/(8043KM)/SCV (8058KM)
with the LRU TROUBLE SHOOT DATA menu information:
NO LRU FAULT DETECTED
Fault Code Number: 217
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-003, 051-099, 401-499, ∞∞49-00-00∞∞∞∞∞∞∞∞∞∞Page 269 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 機載輔助動力 1(24)
