-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASM 31-54/02 ASM 31-54/05 ASM 52-73/01 AWM 52-73-03
 3. Fault Confirmation
__________________
 A. Job Set-up
 (1) Aircraft Maintenance Configuration
 (a) Energize the aircraft electrical circuits
 (Ref. AMM TASK 24-41-00-861-002).

 (b) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. AMM TASK 31-60-00-860-001).

 B. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10
 C. Test
 (1) Make sure that the right forward passenger/crew door is fully closed and the indicator plate shows LOCKED.

 (2) On the ECAM control panel:

 - push the DOOR key to get the DOOR/OXY page.

 (3) On the DOOR/OXY page:

 - make sure that the CABIN indication comes into view amber.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞52-11-00∞∞∞∞∞∞∞∞∞∞Page 210
 Aug 01/05R
 CES

 4. Fault Isolation
_______________

 A. On the Door/Oxy page, if the CABIN indication comes into view amber:
 - do a check for 28VDC between pins A and D of the handle proximity switch (13WV2) (Ref. ASM 31-54/05).
 (1) If there is no 28VDC:
 - do a check for 28VDC at pin S of the indicator light (1WN2).
 (a) If there is 28VDC:
 - repair the wiring as necessary.
 1 If there is no 28VDC:
_
 - do a check for 28VDC between pins A and U of the indicator light (1WN2).
 a If there is 28VDC:
_
 - replace the IND LT-SLIDE ARMED, FWD R DOOR (1WN2) (Ref. AMM TASK 52-73-21-000-001) and (Ref. AMM TASK 52-73-21-400-001).
 b If there is no 28VDC:
_
 - do a check for 28VDC at pin A2 of the relay 12WN.

 * If there is no 28VDC:

 - replace the RELAY-PWR SPLY SWITCHOVER (12WN) (Ref. ASM 52-73/01).

 * If there is 28VDC:

 - repair the wiring as necessary.

 (2) If there is 28VDC:
 - disconnect the connector of the handle proximity switch (13WV2)

 - install the jumper wire between pins B and C of the connector (13WV2-A) (Ref. ASM 31-54/05)

 - do the test given in Para. 3.C.

 (a) On the Door/Oxy page, if the CABIN indication comes into view green:
 - remove the jumper wire between pins B and C of the connector (13WV2-A)

 - connect the connector of the handle proximity switch (13WV2)

 - adjust the handle proximity switch (13WV2) with the door checking tool (Ref. AMM TASK 52-71-00-820-002) or with the ECAM system (Ref. AMM TASK 52-71-00-820-002).

 1 On the Door/Oxy page, if the CABIN indication comes into view
_
 amber:

 - replace the PROX SW-HANDLE, R FWD PAX/CREW DOOR (13WV2) (Ref. AMM TASK 52-71-11-000-001) and (Ref. AMM TASK 52-71-11-400-001).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞52-11-00∞∞∞∞∞∞∞∞∞∞Page 211
 Aug 01/05R CES

 (b) On the Door/Oxy page, if the CABIN indication comes into view amber:
 - remove the jumper wire between pins B and C of the connector (13WV2-A)

 - connect the connector of the handle proximity switch (13WV2)

 - do a check for 28VDC between pins A and D of the hook proximity switch (11WV2) (Ref. ASM 31-54/05).

 1 If there is no 28VDC:
_
 - repair the wiring as necessary.
 2 If there is 28VDC:
_
 - disconnect the connector of the hook proximity switch (11WV2)

 - install the jumper wire between pins B and C of connector (11WV2-A) (Ref. ASM 31-54/05)

 - do the test given in Para. 3.C.

 a On the Door/Oxy page, if the CABIN indication comes into
_
 view green:

 - remove the jumper wire between pins B and C of the connector (11WV2-A)

 - connect the connector of the hook proximity switch (11WV2)

 - adjust the hook proximity switch (11WV2) with the door R checking tool (Ref. AMM TASK 52-71-00-820-001) or with R the ECAM system (Ref. AMM TASK 52-71-00-820-001).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 艙門 DOORS(26)