- ENGINE/2/FADEC A/AND EIU 2 (2KS2)

 - ENGINE/ENG2/FADEC B (4KS2)

 - connector J3 at the ECU (4000KS)

 - harness J3

 - ECU (4000KS)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit R (ECU)(4000KS) AMM 73-25-34-000-040 Removal of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-25-34-400-040 Installation of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
 Engine non Motoring)
 ASM 73-25/05
 ASM 73-25/10

 3. Fault Confirmation
__________________
 A. Table of the circuit breakers used in this procedure:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU ENGINE/2/FADEC A/AND EIU 2 2KS2 A05 121VU ENGINE/ENG2/FADEC B 4KS2 Q40
 B. Do the operational test of the FADEC 2A on the ground (with engine motoring) (Ref. AMM TASK 73-29-00-710-040).
 F 『 EEFF : ALL E ∞∞71-50-00∞∞∞∞∞∞∞∞∞∞Page 231
 E E Aug 01/99 E E ECES
E

 F 『
 E C F M E
 E E
 E 56 E
 E E

 4. Fault Isolation
_______________
 A. If the test gives the maintenance message EIU (ARINC), J3:
 - do a visual check of the connector J3 at the ECU (4000KS) for integrity (Ref. ASM 73-25/10).
 (1) If the fault continues do a check of the status of circuit breakers 2KS2 and 4KS2 (Ref. ASM 73-25/05).
 (a) If the circuit breakers 2KS2 and 4KS2 are closed:
 - do a check for 28VDC at EIU 2 pins AC/9, 11.
 1 If there is 28VDC:
_
 - replace the EIU-2 (1KS2) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040).
 2 If there is not 28VDC:
_
 - do a check of the wiring between the circuit breakers 2KS2 and 4KS2 and the EIU 1 pins AC/9, 11.

 - if there is no continuity:

 - repair the wiring.

 - if there is continuity:

 - replace the ENGINE/2/FADEC A/AND EIU 2 (2KS2) and/or ENGINE/ENG2/FADEC B (4KS2).

 (b) If the circuit breakers 2KS2 and/or 4KS2 are open:
 - close them.
 1 If they trip again:
_
 - replace the EIU-2 (1KS2) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040).
 a If the fault continues:
_
 - do a check of the wiring for short to ground between the circuit breakers 2KS2 and/or 4KS2 and the EIU 1.

 - if the wiring is not correct:

 - repair it.

 - if the wiring is correct:

 - replace the ENGINE/2/FADEC A/AND EIU 2 (2KS2) and/or ENGINE/ENG2/FADEC B (4KS2).

 (2) If the fault continues:

 - replace the harness J3.

 (3) If the fault continues:

 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 B. Do the test given in Para. 3.A.
 F 『 EEFF : ALL E ∞∞71-50-00∞∞∞∞∞∞∞∞∞∞Page 232
 E E Aug 01/99 ERE ECES
E

 F 『
 E C F M E
 E E
 E 56 E
 E E

 TASK 71-50-00-810-813
 Loss of the ADIRU1 Signal to the ECU on Engine 1
 1. Possible Causes
_______________
 - harness J3

 - ADIRU-1 (1FP1)

 - ECU (4000KS)

 - aircraft wiring between the ADIRU1 (1FP1) and the connector 402VC1 on the pylon junction box

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3) AMM 34-12-34-400-001 Installation of the ADIRU (1FP1, 1FP2, 1FP3) R AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit R (ECU)(4000KS) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
 Engine non Motoring)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 動力裝置 POWER PLANT(19)