Removal of the Hydromechanical Unit (HMU)
Installation of the Hydromechanical Unit (HMU)
Removal of the Electronic Control Unit (ECU)(4000KS)
Installation of the Electronic Control Unit
(ECU)(4000KS)
Operational Test of the FADEC on the ground (with
Engine Motoring)
Removal of the Low Pressure Turbine Active Clearance
Control Valve (LPTACC).
Installation of the Low Pressure Turbine Active
Clearance Control Valve (LPTACC).
A. Do the operational test of the FADEC 2B on the ground (with engine motoring) (Ref. AMM TASK 73-29-00-710-040).
NOTE : If ECU 1820M36P02 or 1820M89P02 is installed, the confirmation
____ test is not required.
4. Fault Isolation
_______________
R A. This fault is generated if the actual valve position disagrees with the
R demanded valve position for a set time interval.
R (1) If the failure message LPTC VLV (POS), HMU is not confirmed:
R (a) No maintenance action is required.
F 『
∞∞75-22-00∞∞∞∞∞∞∞∞∞∞Page 241
EEFF : ALL E
E E Feb 01/02
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
R (2) If the failure message LPTC VLV (POS), HMU is not confirmed but is
R repetitive:
R NOTE : No maintenance action is required unless the fault becomes too____
R repetitive.
R - do the following steps until the fault is corrected.
R (a) Replace the LPTC valve (Ref. AMM TASK 75-22-10-000-001) and (Ref.
R AMM TASK 75-22-10-400-001).
R (b) If the fault continues during the subsequent flights:
R - replace the HMU (Ref. AMM TASK 73-21-10-000-001) and (Ref. AMM
R TASK 73-21-10-400-001).
R (c) If the fault continues during the subsequent flights:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and
R (Ref. AMM TASK 73-21-60-400-001).
R (3) If the failure message LPTC VLV (POS), HMU is confirmed:
R (a) Replace the LPTC valve (Ref. AMM TASK 75-22-10-000-001) and (Ref.
R AMM TASK 75-22-10-400-001).
R (b) If the fault continues:
R - replace the HMU (Ref. AMM TASK 73-21-10-000-001) and (Ref. AMM
R TASK 73-21-10-400-001).
R (c) If the fault continues:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and
R (Ref. AMM TASK 73-21-60-400-001).
R
B. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞75-22-00∞∞∞∞∞∞∞∞∞∞Page 242
E E Feb 01/02 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
ECU COOLING SYSTEM - FAULT ISOLATION PROCEDURES
_______________________________________________ TASK 75-24-00-810-805 Failure of the Control of the ECU Cooling Eductor Valve through the Two
Channels on Engine 1
1. Possible Causes
_______________
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with Engine non Motoring)
3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 1A and 1B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞75-24-00∞∞∞∞∞∞∞∞∞∞Page 201
E E Feb 01/98 E E ECES
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 大氣 AIR(36)
