F 『
 E C F M E
 E E
 E 56 E
 E E
 4 If the fault continues:

_
 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 5 If the fault continues:
_
 - replace the harness HJ7 (Ref. AMM TASK 73-21-50-000-040) and (Ref. AMM TASK 73-21-50-400-040).
 (3) If the failure message HPTC VLV (POS), HMU on channel 1A is confirmed:
 (a) Disconnect the harness HJ7 from the ECU and do a check of resistance between: . pins 23 and 24 (17 to 23 Ohms).
 1 If the resistance values are in the specified limits:
_
 - replace the High Pressure Turbine Clearance Control (HPTCC) valve (Ref. AMM TASK 75-21-10-000-002) and (Ref. AMM TASK 75-21-10-400-002).
 a If the fault continues:
_
 - replace the Hydromechanical Unit (HMU) (Ref. AMM TASK 73-21-10-000-002) and (Ref. AMM TASK 73-21-10-400-002).
 b If the fault continues:
_
 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 c If the fault continues:
_
 - replace the harness HJ7 (Ref. AMM TASK 73-21-50-000-040) and (Ref. AMM TASK 73-21-50-400-040).
 (b) If the resistance values are out of the specified limits:
 - disconnect the harness HJ7 from the HMU and do a check of the HMU resistance between: . pins 23 and 24 (17 to 23 Ohms).
 1 If the resistance values are in the specified limits:
_
 - replace the harness HJ7 (Ref. AMM TASK 73-21-50-000-040) and (Ref. AMM TASK 73-21-50-400-040).
R 2_If the resistance values are out of the specified limits:
 - replace the Hydromechanical Unit (HMU) (Ref. AMM TASK 73-21-10-000-002) and (Ref. AMM TASK 73-21-10-400-002).
 NOTE : Tighten the connector by hand plus one eighth of a
____ turn. If necessary use soft nose pliers.
 F 『 EEFF : ALL E ∞∞75-21-00∞∞∞∞∞∞∞∞∞∞Page 203
 E E Nov 01/01 E E ECES
E

 F 『
 E C F M E
 E E
 E 56 E
 E E
 B. Do the test given in para. 3.

 (1) No additional maintenance action is required if the fault is not confirmed.
R (2) Continue the fault isolation procedure if the fault continues.
 F 『 EEFF : ALL E ∞∞75-21-00∞∞∞∞∞∞∞∞∞∞Page 204
 E E Nov 01/01 E E ECES
E TASK 75-21-00-810-804

 F  『
 E  C F M  E
 E  E
 E  56  E
 E  E

 Failure of the HPTCC Valve Channel A on Engine 2
 1. Possible Causes_______________
 - TCC sensor(s)

 - High Pressure Turbine Clearance Control (HPTCC) Valve

 - Hydromechanical Unit (HMU)

 - ECU (4000KS)

 - harness HJ7

 - High Pressure Turbine Clearance Control (HPTCC) valve

 2. Job Set-up Information______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
AMM 73-21-10-000-002  Removal of the Hydromechanical Unit (HMU)
 AMM 73-21-10-400-002  Installation of the Hydromechanical Unit (HMU)
 AMM 73-21-50-000-040  Removal of the HJ7 Harness
 AMM 73-21-50-210-002  Visual Inspection of the Wiring Harnesses
 AMM 73-21-50-400-040  Installation of the HJ7 Harness
 AMM 73-21-60-000-001  Removal of the Electronic Control Unit (ECU)(4000KS)
 AMM 73-21-60-400-001  Installation of the Electronic Control Unit (ECU)(4000KS)
 AMM 73-21-70-000-002  Removal of the High Pressure Turbine Clearance Control (HPTCC) Sensor
 AMM 73-21-70-400-002  Installation of the High Pressure Turbine Clearance Control (HPTCC) Sensor
 AMM 73-29-00-710-040  Operational Test of the FADEC on the Ground (with Engine non Motoring)
 AMM 75-21-10-000-002  Removal of the High Pressure Turbine Active Clearance Control (HPTACC) Valve
 AMM 75-21-10-400-002  Installation of the High Pressure Turbine Active Clearance Control (HPTACC) Valve
 3. Fault Confirmation__________________
 A. Do the operational test of the FADEC 2A on the ground with engine non motoring (Ref. AMM TASK 73-29-00-710-040).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 大氣 AIR(6)