F 『
E C F M E
E E
E 56 E
E E
R B. If the test does note give the maintenance message VSV ACT, J11, ECU:
R - No maintenance action is required.
R C. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞75-32-00∞∞∞∞∞∞∞∞∞∞Page 213
E E May 01/04 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 75-32-00-810-806
Loss of the feedback Signal from the VSV through the Channel A on Engine 2
1. Possible Causes
_______________
- harness J11
- ECU (4000KS)
- harness CJ11R
- VSV actuator
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 73-21-50-000-026 Removal of the CJ11R Harness
AMM 73-21-50-000-044 Removal of the HJ11 Harness
AMM 73-21-50-400-026 Installation of the CJ11R Harness
AMM 73-21-50-400-044 Installation of the HJ11 Harness
R AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit
R (ECU)(4000KS) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with Engine non Motoring) AMM 75-32-10-000-002 Removal of the Variable Stator Vane (VSV) Actuators AMM 75-32-10-400-002 Installation of the Variable Stator Vane (VSV) Actuators ASM 73-25/18
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the FADEC 2A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. If the test gives the maintenance message VSV ACT, J11, ECU:
- do a check for open or short to ground of the harness J11 between the ECU (4000KS) and the 6 o'clock junction box, between the 6 o'clock junction box and the VSV LVDT (Ref. ASM 73-25/18).
(1) If the wiring is not correct:
- repair the above wiring.
F 『 EEFF : ALL E ∞∞75-32-00∞∞∞∞∞∞∞∞∞∞Page 214
E E May 01/04 E E ECES
E F 『 E C F M E E E E 56 E E E
(2) If the wiring is correct:
- disconnect the cable J11 from the ECU (4000KS) and do a resistance check of the cable J11 between: . pins 12 and 28 (400 to 600 Ohms) . pins 26 and 27 (100 to 180 Ohms) . pins 10 and 25 (100 to 180 Ohms) . pins 12 and 11 (> 10 Megohms) . pins 26 and 11 (> 10 Megohms) . pins 10 and 11 (> 10 Megohms) . pin 12 and the ground (> 10 Megohms) . pin 26 and the ground (> 10 Megohms) . pin 10 and the ground (> 10 Megohms).
(a) If the resistance values are in the specified limits:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(b) If the resistance values are out of the specified limits:
- disconnect the cable J11 from the cable CJ11R at the 6 o'clock junction box and do a resistance check of the cable CJ11R between: . pins 4 and 14 (400 to 600 Ohms) . pins 1 and 6 (100 to 180 Ohms) . pins 15 and 27 (100 to 180 Ohms) . pins 4 and 5 (> 10 Megohms) . pins 1 and 5 (> 10 Megohms) . pins 15 and 5 (> 10 Megohms) . pin 4 and the ground (> 10 Megohms) . pin 1 and the ground (> 10 Megohms) . pin 15 and the ground (> 10 Megohms).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 大氣 AIR(76)
