E E Aug 01/99 E E ECES
E F 『 EEFF : ALL E ∞∞80-11-00∞∞∞∞∞∞∞∞∞∞Page 203
F 『
E C F M E
E E
E 56 E
E E
R R R a_ If the resistance values are in the specified limits: - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001), - repeat the fault confirmation given in Para.3.A if the fault continues.
R R R b_ If the resistance values are out of the specified limits:- replace the harness with the resistance values out of the limits: . harness HJ9 (Ref. AMM TASK 73-21-50-000-042) and (Ref. AMM TASK 73-21-50-400-042), . harness HJ10 (Ref. AMM TASK 73-21-50-000-043) and (Ref. AMM TASK 73-21-50-400-043).
B. Do the test given in Para. 3.A.
(1) No additional maintenance action is required if the fault is not confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
E E Aug 01/99 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 80-11-00-810-802
Failure of the Starter Shutoff Valve Switch on Engine 2
1. Possible Causes
_______________
R - starter shutoff valve R - ECU (4000KS) R
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-50-000-042 Removal of the HJ9 Harness AMM 73-21-50-000-043 Removal of the HJ10 Harness AMM 73-21-50-210-001 Visual Inspection of the Wiring Harness AMM 73-21-50-400-042 Installation of the HJ9 Harness AMM 73-21-50-400-043 Installation of the HJ10 Harness AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring)
AMM 80-11-20-000-003 Removal of the Starter Shutoff Valve
AMM 80-11-20-400-003 Installation of the Starter Shutoff Valve
3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 2A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. This failure message is generated if channel A and B switches of the R starter shutoff valve disagree.
(1) If the failure message SAV (SW) J9/J10, ECU* is not confirmed: R
R (a) No maintenance action is required.
(2) If the failure message SAV (SW) J9/J10, ECU* is not confirmed but is repetitive:
- replace the starter shutoff valve (Ref. AMM TASK 80-11-20-000-003) and (Ref. AMM TASK 80-11-20-400-003).
F 『 EEFF : ALL E ∞∞80-11-00∞∞∞∞∞∞∞∞∞∞Page 204
E E Aug 01/99 E E ECES
E F 『 EEFF : ALL E ∞∞80-11-00∞∞∞∞∞∞∞∞∞∞Page 205
F 『
E C F M E
E E
E 56 E
E E
R R R (a) If the failure continues during the subsequent flights: - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
R (b) If the failure continues during the subsequent flights: - replace the harness HJ9 (channel A) (Ref. AMM TASK 73-21-50-000-042) and (Ref. AMM TASK 73-21-50-400-042). - replace the harness HJ10 (channel B) (Ref. AMM TASK 73-21-50-000-043) and (Ref. AMM TASK 73-21-50-400-043).
R (3) If the failure message SAV (SW) J9/J10, ECU* is confirmed: - disconnect the harnesses HJ9 (channel A) and HJ10 (channel B) from the starter shutoff valve.
R (a) Visually examine the receptacles and the connectors for damaged pins or contamination (Ref. AMM TASK 73-21-50-210-001).
R 1_ If damage is found: - repair or replace as required.
R R 2_ if no damage is found:- do an electrical resistance test through the starter shutoff valve for both channels between: . pin 1 and pin 2 (15 to 60 ohms) . pin 1 and pin 5 (> 10 megohms) . pin 1 and the ground (> 10 megohms).
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 STARTING 起動(11)
