R AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit
R (ECU)(4000KS) AMM 73-29-00-710-040 Operational Test of the FADEC on the ground (with Engine Motoring) AMM 80-11-20-000-003 Removal of the Starter Shutoff Valve AMM 80-11-20-400-003 Installation of the Starter Shutoff Valve ASM 74-31/01
3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 2A on the ground (with engine motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. If the test gives the maintenance message SAV (SOL), J9, ECU:
- do a check for open or short to ground of the harness J9 between the ECU (4000KS) and the starter shutoff valve solenoid, pins J9/11, 12 to pins J9/1, 2 (Ref. ASM 74-31/01).
(1) If the wiring is not correct:
- repair the above wiring.
(2) If the wiring is correct:
- disconnect the harness J9 from the ECU (4000KS) and do a check of the ECU resistance cable between: . pins 11 and 12 (15 to 60 Ohms) . pins 11 and 3 (> 10 Megohms) . pins 11 and ground (> 10 Megohms).
F 『 EEFF : ALL E ∞∞80-11-00∞∞∞∞∞∞∞∞∞∞Page 217
E E May 01/99 E E ECES
E F 『 E C F M E E E E 56 E E E (a) If the resistance values are in the specified limits:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) (Ref. AMM TASK 73-21-60-400-001).
(b) If the resistance values are out of the specified limits:
- disconnect the harness J9 from the starter shutoff valve and do a check of the starter shutoff valve resistance between: . pins 1 and 2 (15 to 60 Ohms) . pins 1 and 5 (> 10 Megohms) . pins 1 and ground (> 10 Megohms).
1 If the resistance values are in the specified limits:
_
- replace the harness J9 (Ref. AMM TASK 73-21-50-000-042) (Ref. AMM TASK 73-21-50-400-042).
2 If the resistance values are out of the specified limits:
_
- replace the starter shutoff valve (Ref. AMM TASK 80-11-20-000-003) (Ref. AMM TASK 80-11-20-400-003).
B. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞80-11-00∞∞∞∞∞∞∞∞∞∞Page 218
E E May 01/99 ERE
ECES E
F 『
E C F M E
E E
E 56 E
E E
TASK 80-11-00-810-808
Failure of the Control of the Starter Shutoff Valve Solenoid through the
Channel B on Engine 2
1. Possible Causes
_______________
- ECU (4000KS)
- harness J10
- starter shutoff valve
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 73-21-50-000-043 Removal of the HJ10 Harness
AMM 73-21-50-400-043 Installation of the HJ10 Harness
R AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit
R (ECU)(4000KS) AMM 73-29-00-710-040 Operational Test of the FADEC on the ground (with Engine Motoring) AMM 80-11-20-000-003 Removal of the Starter Shutoff Valve AMM 80-11-20-400-003 Installation of the Starter Shutoff Valve ASM 74-31/01
3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 2B on the ground (with engine motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. If the test gives the maintenance message SAV (SOL), J10, ECU:
- do a check for open or short to ground of the harness J10 between the ECU (4000KS) and the starter shutoff valve solenoid, pins J10/11, 12 to pins J10/1, 2 (Ref. ASM 74-31/01).
(1) If the wiring is not correct:
- repair the above wiring.
(2) If the wiring is correct:
- disconnect the harness J10 from the ECU (4000KS) and do a check of the ECU resistance cable between: . pins 11 and 12 (15 to 60 Ohms) . pins 11 and 3 (> 10 Megohms) . pins 11 and ground (> 10 Megohms).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 STARTING 起動(16)
