SYSTEM TESTER SWITCH POSITION  MINIMUM RESISTANCE Megohms 
A - GND (Hi Z to Airplane Ground) B - GND (Tank Unit to Lo Z to Airplane Ground) C - GND (Compresator Lo Z to Airplane Ground) A - C (Hi Z to COMP Lo Z)  10 10 10 250 

502 
May 01/00  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  28-41-91 Page 603 

F.  SIMMONDS (JCAIR) PSD40 OR PSD60 SYSTEM TESTER, Do the Resistance Check
(1)  
At the applicable spar location (Fig. 601), disconnect the electrical connector from the bussing plug.

(2)  
Connect the test harness to the bussing plug and the system tester.

NOTE: Do not connect the test harness to the connector that goes to the indicator.

(3)  
Set the power switch on the test unit to ON.

(4)  
Set the FUNCTION SEL switch to MEG (not SELF TEST MEG) (PSD40-1) or set the FUNCT switch to MEASURE EXT (PSD60-1).

(5)  
Set the FUNCTION MEASURE switch (PSD40-1) or set the SELECT switch (PSD60-1) to LOZ - HIZ.

(6)  
Read the total resistance for the tank units.

(a) Make sure the resistance shown on the test unit is more than 250 megohms.

(7)  
Set the FUNCTION MEASURE switch (PSD40-1) or set the SELECT switch (PSD60-1) to COMP-HIZ.

(8)  
Read the total resistance for the compensator.

(a)  Make sure the resistance shown on the system tester is more than 250 megohms.

(9)  
Set the FUNCTION MEASURE switch (PSD40-1) or set the SELECT switch (PSD60-1) to each of the SHLD or GND positions.

(a) Make sure the minimum resistance agrees with the values shown in this table:

(10)
If a resistance value is less than the minimum value, do a check for a short circuit in one of these areas (Ref 28-41-21/501 or 28-41-02/501):

SYSTEM TESTER SWITCH POSITION  MINIMUM RESISTANCE Megohms 
HIZ-GND (Hi Z to Airplane Ground) LOZ-GND (Tank Unit to Lo Z to Airplane Ground) COMP-GND (Compresator Lo Z to Airplane Ground) LOZ-SHLD (Tank Unit to Lo Z to Shield) COMP-SHLD (Compresator Lo Z to Coax Shield) HIZ-SHLD (Hi Z to Coax Shield) SHLD-GND (Coax Shield to Airplane Ground)  10 10 10 1 1 1 10 

(a)  The tank unit
1) The wires that connect the tank unit to the FQIS
2) The plug that connects the tank unit to the wire bundle
3) The receptacle that connects the tank unit to the wire bundle.

28-41-91 May 01/00 Page 604
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.

(b)  The compensator unit 1) The wires that connect the compensator unit to the FQIS 2) The plug that connects the compensator unit to the wire bundle 3) The receptacle that connects the compensator unit to the wire bundle.
G.  BARFIELD 8000 SYSTEM TESTER, Do the Resistance Check
(1)  
At the applicable spar location (Fig. 601), disconnect the electrical connector from the bussing plug.

(2)  
Connect the test harness to the bussing plug and the system tester.

NOTE: Do not connect the test harness to the connector that goes to the indicator.

(3)  
Set the TEST FUNCTION switch on the test unit to INSULATION.

(4)  
Set the battery switch to ON.

(5)  
Turn the METER ADJUST knob until the meter is at its maximum value.

(6)  
Set the INS TEST POINTS switch to LO-Z/HI-Z

(7)  
Read the total resistance for the tank unit.

(a) Make sure the resistance shown on the test unit is more than 250 megohms.

(8)  
Set the INS TEST POINTS switch to each of the SHLD or GND positions shown below.

(a)  Make sure that each resistance shown on the test unit is more than the applicable minimum resistance:

(9)  
Disconnect the UNSHIELDED wire bundle of the test harness from the INSULATION LO-Z receptacle on the test unit.

(10)
Connect the COMP wire bundle to the INSULATION LO-Z receptacle.

(11)
Set the INS TEST POINTS switch to LO-Z/HI-Z.

(12)
Read the resistance of the compensator.

(a) Make sure the resistance shown on the system tester is more than 250 megohms.

(13)
Set the INS TEST POINTS switch to each of the SHLD or GND positions shown below.

(a)  Make sure that each resistance shown on the test unit is more than the applicable minimum resistance.

(14)
If a resistance value is less than the minimum value, do a check for a short circuit in one of these areas (Ref. 28-41-21/501 or 28-41-02/501):

(a)  
The tank unit
1) The wires connecting the tank unit to the FQIS
2) The plug connecting the tank unit to the wire bundle
3) The receptacle connecting the tank unit to the wire bundle.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 燃油 FUEL(181)