曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

B.  With the landing gear up and locked, the indicator and warning lights will be off if the landing gear control lever is in UP or OFF position. When the control lever is placed in DN position, the red warning lights will come on and remain on while the gear unlock and extend to down and locked. As the gear lock in down position, the red warning lights wil1 go off and the green indicator lights will come on and remain on until power is removed from the circuit.
C.  If the flaps are extended beyond the minimum approach and climb configuration before the landing gear are down and locked, the flap landing warning switch will close to complete the circuit through a solid-state circuit in the landing gear electrical module to sound the warning horn. When the airplane configuration is changed either by extending the gear or retracting the flaps, a circuit is opened through the solid-state circuit to silence the warning horn.
D.  If an engine thrust lever is moved into idle range, the landing gear warning horn switch will close and, if the landing gear are not down and locked, complete the circuit through a solid-state circuit in the landing gear electrical module causing the warning horn to sound and the red warning lights to come on. Advancing the engine thrust lever or extending the landing gear will silence the warning horn and turn off the warning lights. The warning horn reset switch may be used to silence the warning horn.
503 
32-61-0 Page 10  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  Aug 15/77 

K42021 H80062
521  Landing Gear Position Indicating and Warning Schematic 
Aug 15/77  Figure 7  32-61-0 
Page 11 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

Landing Gear Position Indicating and Warning Functional Schematic Diagrams  521 
32-61-0  Figure 8  Aug 15/77 
Page 12 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

LANDING GEAR POSITION INDICATING AND WARNING SYSTEM - TROUBLE SHOOTING
1.  General
A.  The trouble shooting charts in the following pages are designed as an aid for locating causes of troubles that may appear in the landing gear position indicating and warning system. The charts are arranged so that by starting at the top and proceeding downward the trouble may be isolated and corrected. These charts do not cover every possible trouble, however they may be used as a guide for isolating troubles not covered. No attempt has been made to give detailed instructions for measuring voltages or continuity. These may vary for different airplane configurations. Therefore, the applicable wiring diagrams must necessarily be used in conjunction with the trouble shooting charts. Prior to trouble shooting, the engine pressure ratio function of the engine indicating system must be functioning properly (Ref Chapter 77).
B.  The proximity sensors used in this system fail to the normal nonenergized condition. Therefore if a sensor is shorted or open, the related switch is in its normal nonenergized condition. This condition may be simulated by disconnecting the sensor at the disconnect nearest the sensor or by jumpering the sensor at this point. The position switch circuits may be actuated by placing a strip of ferrous material against the face of the sensor or by replacing the sensor with a 1000-ohm resistor. Sensors may be checked for malfunction by measuring dc resistance between sensor leads. The resistance between the blue and yellow leads should be 350 +35 ohms. The resistance between the red and yellow leads should be 30 +6 ohms.
C.  In the following charts, the airplane will be in one of the following conditions unless specified otherwise:
(1)  
Airplane on ground; electrical power on; all circuit breakers closed; gear down and locked; lockpins installed; hydraulic system depressurized; throttles advanced; landing gear lever in OFF position.

WARNING:  CHECK THAT GROUND LOCK ASSEMBLIES ARE INSTALLED IN ALL LANDING GEAR TO PREVENT INADVERTENT OPERATION OF GEAR. INJURY TO PERSONNEL AND/OR EQUIPMENT COULD RESULT IF GEAR RETRACTS.

(2)  
Airplane on jacks; electrical power on; all circuit breakers closed; gear up and locked; hydraulic system depressurized; throttles advanced; landing gear lever in OFF position.

NOTE:  It may be necessary to pressurize the hydraulic system momentarily to obtain flap position called for (Ref 29-11-0 MP and 29-12-0 MP).
D.  Landing gear position indicating and warning system trouble symptoms are best identified by performing a test of the system (Ref Landing Gear Position Indicating and Warning System -A/T). If the system does not react as specified, proceed to the following charts.
2.  Trouble Shooting Charts
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 起落架 LANDING GEAR(184)