NOTE: 1. NO WING FUEL
2. CG LOCATION AS NOTED
GROUND
CLEARANCE
AFT BODY ON THE GROUND
95
NOSE GEAR JACKING HEIGHT - INCHES
90 80 70
60 50 40 30
20 10
0
TAIL HEIGHT ABOVE THE GROUND - FEET
EXAMPLE FOR 737-300 AIRPLANES HAVING OEW 65,000 - 75,000 POUNDS
AND CG BETWEEN 18% AND 20% MAC
Vertical Tail Height versus Nose Gear Jack Height Figure 202
T97646
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
07-13-00
ALL ú ú 03 Page 203 ú Jul 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(6) S 972-042Find the nose height that is necessary to get the tail clearance (Fig. 202).
(7) S 212-012Make sure the nose landing gear is in its neutral position.
(8) S 492-013Install the shock absorber around the nose gear.
NOTE:____ Install the shock absorber to prevent too much compression on the inner cylinder. This will prevent damage to the lower fuselage.
(9) S 492-014Install the dolly on the nose gear: (a) Remove the rear lock bar from the dolly. (b) Put the dolly in the center of the nose gear. (c) Disconnect the torque links on the nose gear. (d) Install the dolly lock bar behind the tires.
STRUT POSITION DIMENSION X
FULLY COMPRESSED 13.5 INCHES
FULLY EXTENDED 25.5 INCHES
Nose Gear Shock Strut Extension
Figure 203
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
07-13-00
ALL ú ú 03 Page 204 ú Jul 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
D. Procedure
S 212-015
(1)
Make sure all the landing gear downlocks are installed.
S 982-016
(2)
Loosely put chocks on the main gear wheels.
S 212-017
(3)
Make sure the airplane brakes are released.
S 582-011
WARNING:_______DO NOT STAY NEAR THE LEADING EDGE SLATS. THEY CAN MOVE AUTOMATICALLY DURING MAINTENANCE. THIS CAN CAUSE INJURY TO PERSONS.
CAUTION:_______DO NOT LIFT THE AIRPLANE NOSE MORE THAN 84 INCHES. THE AIRPLANE WILL NOT BE STABLE IF YOU LIFT THE NOSE MORE THAN 84 INCHES. THIS CAN CAUSE DAMAGE TO THE AIRPLANE.
(4)
Lift the airplane nose to the necessary height with the dolly.
S 982-019
(5)
Operate the gear scoop "DOWN" to hold the dolly in the uplock position.
S 222-021
CAUTION: DO NOT TOW THE AIRPLANE WHEN THE STRUT EXTENSION
_______ (DIMENSION "X") IS MORE THAN 23 INCHES. THIS CAN CAUSE DAMAGE TO THE CENTERING CAMS ON THE NOSE GEAR.
(6) Make sure the Dimension "X" (Fig. 203) is not more than 23 inches.
(a) If Dimension "X" is more than 23 inches, release the strut pressure until Dimension "X" is 23 inches or less.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
07-13-00
ALL ú ú 02 Page 205 ú Jul 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b) Adjust the strut limit, if it is necessary.
TASK 07-13-00-282-002
3. Balance Check for the Tilted Airplane (Fig. 204 to Fig. 213)____________________________________________________________
A. General
(1) When you lift the airplane nose, the center of gravity of the airplane moves aft with respect to the main gear axle. This movement, plus the wind, upgrades, and fuel movement can cause the airplane to move. This can make the aft fuselage of the airplane touch the ground. Thus, you must complete a balance check form to make sure the airplane will be stable. Add the ballast, if it is necessary. You can use the dolly as a ballast. To do this, attach it to the nose gear wheels.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 LIFTING AND SHORING(12)
