S 015-029-C00
(2)
Disconnect the plug, D424, from the pneumatic starter valve.
S 765-010-C00
(3)
Do the steps that follow to measure the voltage of the right and left ignition circuits on the applicable engine:
(a)
Put the start lever in the CUTOFF position.
(b)
Put the engine ignition switch in the BOTH position and the start switch in the GRD position and hold. 1) Make sure the AC voltage across pin B to ground of the
connector, D420, is 0 |6 volts AC. 2) Make sure the AC voltage across pin B to ground of the connector, D1214, is 0 |6 volts AC.
(c)
Put the start lever in the IDLE position.
(d)
Put the engine ignition switch in the BOTH position and the start switch in the GRD position. 1) Make sure the AC voltage across pin B to ground of the
connector, D420, is 115 |6 volts AC. 2) Make sure the AC voltage across pin B to ground of the connector, D1214, is 115 |6 volts AC.
(e)
Put the engine ignition switch in the BOTH position and the start switch in the OFF position. 1) Make sure the AC voltage across pin B to ground of the
connector, D420, is 0 |6 volts AC. 2) Make sure the AC voltage across pin B to ground of the connector, D1214, is 0 |6 volts AC.
(f)
Put the engine ignition switch in the IGN L position and the start switch in the CONT position. 1) Make sure the AC voltage across pin B to ground of the
connector, D420, is 0 |6 volts AC.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
74-31-12
ALL ú ú C03 Page 504 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
2) Make sure the AC voltage across pin B to ground of the connector, D1214, is 115 |6 volts AC.
(g)
For the applicable engine, open these circuit breakers and attach DO-NOT-CLOSE tags: 1) P6 Load Control Center
a) ENG 1 L IGN
b) ENG 2 L IGN
(h)
Make sure the AC voltage across pin B to ground of the connector, D1214, is 0 |6 volts AC.
(i)
For the applicable engine, close these circuit breakers and attach DO-NOT-CLOSE tags: 1) P6 Load Control Center
a) ENG 1 L IGN
b) ENG 2 L IGN
(j)
Put the engine ignition switch in the IGN R position and the start switch in the CONT position. 1) Make sure the AC voltage across pin B to ground of the
connector, D420, is 115 |6 volts AC. 2) Make sure the AC voltage across pin B to ground of the connector, D1214, is 0 |6 volts AC.
(k)
For the applicable engine, open these circuit breakers and attach DO-NOT-CLOSE tags: 1) P6 Load Control Center
a) ENG 1 R IGN
b) ENG 2 R IGN
(l)
Make sure the AC voltage across pin B to ground of the connector, D420, is 0 |6 volts AC.
(m)
For the applicable engine, close these circuit breakers and attach DO-NOT-CLOSE tags: 1) P6 Load Control Center
a) ENG 1 R IGN
b) ENG 2 R IGN
(n)
Put the engine ignition switch in the IGN R position and the start switch in the FLT position. 1) Make sure the AC voltage across pin B to ground of the
connector, D420, is 115 |6 volts AC. 2) Make sure the AC voltage across pin B to ground of the connector, D1214, is 115 |6 volts AC.
(o)
Remove the jumper from pin B to ground of the plug, D420.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
74-31-12
ALL ú ú C03 Page 505 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(p) Remove the jumper from pin B to ground of the plug, D1214.
S 765-014-C00
(4) Do the steps that follow to do the start switch holding solenoid check:
(a)
Make sure these circuit breakers are closed:
1) ENG 1 START VALVE
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 點火 IGNITION(37)
