(c)
Remove the two bolts and two nuts that attach the left junction box to the engine flange.
S 034-055-C02
(2) Do these steps to disconnect the connector:
(a)
Disconnect the connector (on the lower extension harness) from the left junction box with the fork wrench.
(b)
Put protective caps on the connector and the receptacle.
S 024-056-C02
(3) Do these steps to remove the probes:
(a)
Remove the two bolts that attach each probe to the engine boss.
(b)
ENGINES WITH EGT AIR DEFLECTORS; Remove the EGT air deflector from each probe.
(c)
Carefully remove the probes from the engine.
(d)
Put protective caps on the probes and the engine bosses.
TASK 77-21-01-404-019-C02
5. Left EGT Thermocouple Harness and Probes Installation_____________________________________________________
A. Equipment
(1) Fork Wrench - AN8508-14, Snap-on Tools Company, 8049-28th St Kenosha, WI 53140
B. Consumable Materials
(1) D00601, Grease, (CP2101) graphite - GP460, Aeroshell 8
C. References
(1)
AMM 71-11-02/201, Fan Cowl Panels
(2)
AMM 77-21-00/501, EGT Indicating System
(3)
AMM 78-31-00/201, Thrust Reverser System
D. Access
(1)
Location Zones
504 Left Engine - Left Side
604 Right Engine - Left Side
(2)
Access Panels
5738L Left Thrust Reverser - Left Engine
5838R Left Thrust Reverser - Right Engine
E. Procedure
S 424-057-C02
(1) Do these steps to install the probes (Fig. 402):
(a)
Remove protective caps from the probes and the engine bosses.
(b)
Carefully install the probes in the engine bosses.
1) Install the lower probe, then the center probe, and then the upper probe.
(c)
Apply a thin layer of antiseize compound to the bolts that attach the probes.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
9 PROBE EGT SYSTEM (RIGID MOUNT) ú 77-21-01
ú CONFIG 2 ú C02 Page 410 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(d) ENGINES WITH EGT AIR DEFLECTORS;
Put the EGT air deflector on each probe.
NOTE: A deflector is not installed at the No. 1 probe.
____
(e) Install the two bolts to attach each probe. 1) Tighten each bolt to 100-110 pound-inches (11.5-12.5 N.m). 2) Install a lockwire or a safety cable on each bolt.
S 434-162-C02
(2) Do these steps to attach the connector:
(a)
Remove protective caps from the connector and the receptacle.
(b)
Connect the connector (from the lower extension harness) to the left junction box. 1) Tighten the connector with the fork wrench to
170-190 pound-inches (19-21 N.m). 2) Install a lockwire or a safety cable on the connector.
S 424-059-C02
(3) Do these steps to attach the harness:
(a)
Apply a thin layer of antiseize compound to the bolts.
(b)
Install the two bolts and two nuts that attach the left junction box to the engine flange. 1) Tighten the nut to 100-110 pound-inches (11.5-12.5 N.m).
(c)
Install the clamp half, the bolt, and the nut that attach the harness to the engine bracket at two locations. 1) Tighten the nuts to 30-35 pound-inches (3.5-4 N.m).
(d)
Install the two clamp halves, two bolts, and two nuts that attach the left harness and the lower extension harness to the engine bracket. 1) Tighten the nuts to 30-35 pound-inches (3.5-4 N.m).
F. Put the Airplane Back to Its Usual Condition
S 414-143-C02
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 WHEN YOU CLOSE THE
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 發動機指示 ENGINE INDICATIN(28)
