(3)  
Pressure Tank - must hold 100 psi pressure and have a mechanism for mix materials

 (4)  
Fluid Hose - must be large enough to provide material to the gun at the correct pressure

 C.  Consumable Materials
 (1)  
B00148 Solvent - Methyl Ethyl Ketone (MEK),
 TT-M-261

 (2)  
B0094 Solvent - Toluene (Toluol), TT-T-548

 (3)  
B00151 Solvent - Methyl Isobutyl Ketone (MIBK),
 TT-M-268

 (4)  
B00083 Solvent - Aliphatic Naphtha, TT-N-95,
 Type II

 (5)  
C00038 Griptred - A862 white, Type I, Smooth,
 Goodyear (optional: MIL-W-5044, Type I,
 Color Fed Std 595, 37875 white)

 (6)  
C00038 Griptred - A419A, Black, Type I, Smooth,
 Goodyear (optional: MIL-W-5044, Type I,
 Color Fed Std 595, 37038 Black)

 (7)  
C00038 Griptred - A859, Light dull gray, Type
 I, Smooth, Goodyear
 (optional: MIL-W-5044, Type I, Color
 Fed Std 595, 36440 light dull gray)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 51-24-09
 ALL  ú ú 01 Page 701 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (8)  
C00038 Griptred - A441A, Dark dull gray, Type
 I, Smooth, Goodyear
 (optional: MIL-W-5044, Type I, Color
 Fed Std 595, 36231 Dark dull gray)

 (9)  
G00383 Paper - Abrasive Aluminum Oxide, 320
 grit (minimum)

 (10)
 G00500 Brush - Paint, Bristle

 (11)
 G00270 Tape - Masking No. 221, 3M Company

 D. Prepare the Surface for Painting
 NOTE: You must apply nonskid coating over primed, or primed
____ and topcoated, surfaces as shown in drawing specifications.
 S 117-066
 WARNING: DO NOT GET THE SOLVENTS IN YOUR MOUTH OR EYES, ON YOUR SKIN OR
_______ CLOTHES. DO NOT BREATHE THE FUMES FROM THESE SOLVENTS. MAKE SURE THE AIR FLOWS FREELY THROUGH THE WORK AREA. USE THE NECESSARY RESPIRATORY PROTECTION. KEEP THESE MATERIALS AWAY FROM SPARKS, FLAME, AND HEAT. THESE SOLVENTS ARE POISONOUS AND FLAMMABLE AND CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  Clean the surface:
 (a)  
If it has been less than 48 hours since you applied the coating, do these steps: 1) Rub the surface with 320 grit (minimum) abrasive paper, if

 it is necessary. 2) Clean the surface with toluene.

 (b)  
If it has been more than 48 hours since you applied the coating, do these steps: 1) Manually clean the surface with toluene. 2) Rub the surface clean with a 320 grit (minimum) aluminum

 oxide abrasive paper, fabric, or disk. 3) Manually clean the surface with MIBK.
 E. Apply the Nonskid Surface
 S 377-003
 (1)
Add aliphatic naphtha to make the coating thin, if it is necessary.

 S 377-004

 (2)  
Apply the nonskid surface with a spray gun or a brush:

 (a)  Make sure the coating is 0.005 to 0.007 inch (6 to 8 ounces for each square yard) thick after it is dry.
 NOTE: The dry thickness is the distance from the primer to the
____
 external surface.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 51-24-09
 ALL  ú ú 01 Page 702 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  Let each layer dry for a minimum of 30 minutes.
 S 037-055
 (3)  
Carefully remove the tape before the coating is fully dry.

 S 217-056

 (4)  
Examine the surface to make sure the coating is dry before you touch it.

 NOTE: The finish is hard after 24 hours at 70°F.
____
 F. Repair the Nonskid Surface (Small Damaged Areas).
 S 117-007
 (1)  Clean the area to be repaired as follows:
 WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 結構 STRUCTURES(48)