EQUIPMENT.
 (13)
 Do this procedure:  Thrust Reverser Deactivation for Ground Maintenance (AMM 78-31-00/201).

 S 015-164-N00

 (14)
 Open the core cowl panels (AMM 71-11-06/201).

 S 015-162-N00
 WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 WHEN YOU OPEN THE
_______ THRUST REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
 (15)
 Open the thrust reversers (AMM 78-31-00/201).

 S 795-108-N00

 (16)
 Examine the engine and engine-mounted accessories for signs of fuel, oil and hydraulic leaks.

 NOTE: If an engine turns at speeds below idle, a small quantity
____ of oil leakage can occur. It comes through the carbon seal assembly for the No. 2 bearing. This usually occurs when the engine turns at low speeds for an extended time (when an engine has an extended start/shutdown or when an engine turns freely in the wind). After the engine shutdown, this oil leakage can be on the retention bolts for the variable stator vane at the bottom of the engine. It can also be on the bottom of the nose cone/spinner. This small quantity of oil leakage is permitted.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 71-00-00
 ALL  ú ú N03 Page 567 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
TEST NO. 9 - PERFORMANCE TEST
_____________________________
 S 975-109-N00
 (17) Calculate the pressure ratios for the low pressure compressor and high pressure compressor, N1C, N2C and EGTC values from the stable engine operation data (Fig. 507).
 (a)  
Compare the calculated N1C value to the N1C LIMIT values shown in the N1, N2 and EGT Acceptance Limits table (Fig. 508). 1) The N1C value must be between the N1C MIN LIMIT and N1C MAX

 LIMIT values.

 (b)  
Compare the calculated N2C value to the N2C LIMIT value shown in the N1, N2 and EGT Acceptance Limits table (Fig. 508) 1) The N2C value must be lower than the N2C LIMIT value.

 (c)  
Compare the calculated EGTC value with the EGTC LIMIT value shown on the N1, N2 and EGT Acceptance Limits table (Fig. 508). 1) The EGTC value must be lower than the EGTC LIMIT value.

 (d)  
Review the calculated low pressure compressor ratio. This value can be between 1.9 and 2.1. This is a guideline only.

 NOTE: The ratio values are guidelines only and not
____ acceptance limits. If the calculated ratios are more than the guidelines, check for instrumentation errors or pressure leaks.
 (e)  Review the calculated high pressure compressor ratio. This value can be between 8.9 and 9.7. This is a guideline only.
 NOTE: The ratio values are guidelines only and not
____ acceptance limits. If the calculated ratios are more than the guidelines, check for instrumentation errors or pressure leaks.
 S 965-264-N00
 (18)
 Repair and retest as necessary.

 H.
Put the Airplane Back to Its Usual Condition.

 S 015-112-N00
 (1)  If it is not done, open the thrust reversers with the steps that follow:
 (a)  Open the fan cowl panels (AMM 71-11-04/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 71-00-00
 ALL  ú ú N03 Page 568 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(a) Calculate the pressure ratios: (pressures in the absolute levels)
1. Pressure ratio for the low pressure compressor
PT2.5
=

-0.08
PT2x(òT2)
TT2`C+273.16
òT2 =

288.16
2. Pressure ratio for the high pressure compressor
PS3
=

0.08
PT2.5x(òT2)
(b) Calculate the corrected N1 (rpm):
N1 (rpm)
N1C =

RòT2xKHN1
N1 (rpm) (All models except PW4062) = %N1x36.00 rpm
N1 (rpm) (PW4062 only) = %N1x36.29 rpm
____If engine model/rating is PW4062, 100%N1 = 3629 rpm

NOTE: TT2`C+273.16
RòT2 =  
(KHN1 is found on sheet 2)
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 動(dòng)力裝置 POWER PLANT 1(74)