73-21-07
ALL ú ú N01A Page 468 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
W6 HARNESS BOLT BOLT
W6 HARNESS
SUPPORT TUBE
H NUT SUPPORT TUBE I NUT WASHERS ALUMEL NUTS ALUMEL
EEC THERMOCOUPLE (TT3) PROBE WASHERS CHROMEL CHROMEL NUTS
LEAD GROUND BOLT
FWD BOLT NUT TUBE SUPPORT W6 HARNESS
BRACKET NUT W6 HARNESS
J Figure 405 (Sheet 4) EEC Wiring Harness W6 Installation
E44649
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-07
ALL ú ú N01A Page 469 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES /MAINTENANCE MANUAL ////////////////////////
NUT
SUPPORT
TUBE
FWD
W6
HARNESS BOLT
BOLT K BRACKET
W6
HARNESS
BOLT
SUPPORT TUBE
W6 HARNESS BRACKET
NUT
L
NUT
M
EEC Wiring Harness W6 Installation Figure 405 (Sheet 5)
E44651
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-07
ALL ú ú N01A Page 470 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
5) 6G17 SCU ALT PWR ENG 3
6) 6G25 ENG SCU 3
7) 6G18 SCU ALT PWR ENG 4
8) 6G26 ENG SCU 4
S 014-177-N00
(2) Open the right fan cowl panel (AMM 71-11-04/201).
S 044-178-N00
WARNING: DO THE THRUST REVERSER DEACTIVATION PROCEDURE TO PREVENT THE
_______ OPERATION OF THE THRUST REVERSER. THE ACCIDENTAL OPERATION OF THE THRUST REVERSER CAN CAUSE INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT.
(3)
Do this procedure: Thrust Deactivation for Ground Maintenance (AMM 78-31-00/201).
S 014-179-N00
(4)
Open the right core cowl panel (AMM 71-11-06/201).
S 014-180-N00
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 WHEN YOU OPEN THE
_______ THRUST REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
(5)
Open the right thrust reverser (AMM 78-31-00/201).
S 024-194-N00
(6)
Do these steps to remove the W6 harness from the engine:
(a)
Remove the screws which attach the cover and ground lead to the EGT (TT4.95) thermocouple terminal box (View C). 1) Before you disconnect the cable leads, put a tag on each
lead and terminal stud to help you during the installation.
CAUTION: DO NOT TWIST OR BEND THE WIRE HARNESS MORE THAN NECESSARY
_______
DURING THE REMOVAL OF THE WIRE HARNESS. IF THE WIRE
HARNESS IS TWISTED OR BENT, YOU CAN CAUSE DAMAGE TO THE
WIRE HARNESS.
(b) Remove the nuts and washers which attach the W6 harness leads to the TT4.95 terminal studs (View C). 1) Remove the W6 harness leads from the studs. 2) Install the nuts and washers on the studs.
NOTE: The diameters of the chromel nut, washer, and
____ terminal stud are smaller than the diameter of the alumel nuts, washers, and terminal studs.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-07
ALL ú ú N01A Page 471 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(c) Remove the nuts and washers which attach the W6 harness leads to the TT3 probe (View J). 1) Remove the W6 harness leads from the TT3 probe. 2) Install the nuts and washers on the studs of the TT3 probe.
NOTE: The diameters of the chromel nut, washer, and
____ terminal stud are smaller than the diameters of the alumel nuts, washers, and terminal studs.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機燃油和控制 2(60)
