B. Parts
 ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 2 | Starter | 80-11-01 | 01 | 20 | | | 3 | Quick Attach-Detach Clamp | | | 100 | | | 4 | Packing | | | 15 | | | 6 | Seal | | | 10 | 2......…........…...................................…..........…......…........1
 C. References
 (1)
AMM 12-13-06/301, Engine Starter

 (2)
AMM 71-00-02/401, Power Plant

 (3)
AMM 71-11-04/201, Fan Cowl Panels

 (4)
AMM 71-11-06/201, Core Cowl Panels

 (5)
AMM 72-61-09/401, Starter Drive Coupling

 (6)
AMM 78-31-00/201, Thrust Reverser System

 (7)
AMM 79-21-10/601, Magnetic Chip Detector

 (8)
AMM 80-11-00/501, Engine Starting System

 D. Access
 (1)  
Location Zone
 412 Engine No. 1
 422 Engine No. 2
 432 Engine No. 3
 442 Engine No. 4

 (2)  
Access Panel
 415 and 416 Thrust Reverser - Engine No. 1
 425 and 426 Thrust Reverser - Engine No. 2
 435 and 436 Thrust Reverser - Engine No. 3
 445 and 446 Thrust Reverser - Engine No. 4

 E. Prepare to Install the Starter
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 80-11-01
 ALL  ú ú N01 Page 404 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
S 214-010-N00
 CAUTION: BEFORE YOU INSTALL THE STARTER, MAKE SURE THE NUT ON THE
_______
 STARTER DRIVE COUPLING IS CORRECTLY INSTALLED. IF THE NUT IS
 LOOSE, DAMAGE TO THE GEARBOX CAN OCCUR.

 (1)  Do these steps to examine the starter drive coupling:
 (a)  
Remove the cap from the main gearbox.

 (b)  
Look for the nut on the starter drive coupling.

 (c)  
If the nut is loose, look for a circular gouge or scoring on the front face of the starter output shaft.

 (d)  
If you find damage, you must examine the gearbox magnetic chip detector for bearing material (AMM 79-21-10/601).

 (e)  
If you find bearing material, replace the engine
 (AMM 71-00-02/401).

 (f)  
If you do not find bearing material, replace the loose nut (AMM 72-61-09/401).

 F.  Procedure
 S 424-027-N00
 (1)  Install the starter (Fig. 401):
 NOTE: You can get access to the manual override in the starter
____ valve through the access hole in the left core cowl only when the starter, interconnect duct, and starter valve are correctly aligned.
 (a)  
Remove the caps from the start valve, the interconnect duct (1) and the starter (2).

 (b)  
Lubricate the new packing (4) with the engine oil.

 (c)  
Install the packing (4) on the starter drive shaft.

 (d)  
Apply a thin layer of grease to the splines of the starter drive shaft.

 CAUTION:_______DO NOT LIFT THE STARTER BY THE DRIVE SHAFT. INTERNAL DAMAGE TO THE STARTER CAN OCCUR.

 (e)  
Move the starter (2) to the main gearbox.

 1)  Carefully move the starter forward until the splines on the starter drive coupling and the starter drive shaft engage.

 (f)  
Align the index pin on the QAD adapter with the index hole on the starter flange. 1) Carefully move the starter (2) forward until there is no

 separation between the starter and the QAD adapter.

 (g)  
Install the QAD clamp (3).

 1)  Tighten the QAD clamp nut to 65-75 pound-inches (7.3-8.5 newton-meters).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 80-11-01
 ALL  ú ú N01 Page 405 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起動 STARTING(10)