757 MAINTENANCE MANUAL
STATIC PORT
5-INCH STRIP OF 
VINYL ADHESIVE 
TAPE 
BARRICADE 
TAPE 
STEP 1  STEP 2
PUT ONE END OF THE BARRICADE TAPE OVER  SECURE THE TOP EDGE OF THE BARRICADE TAPE 
THE STATIC PORT TO COVER THE HOLES  WITH 5 INCHES OF VINYL ADHESIVE TAPE 

5-INCH STRIPS OF VINYL ADHESIVE TAPE
8-INCH STRIP OF VINYL ADHESIVE TAPE
STEP 3  STEP 4 
PUT TWO 5-INCH STRIPS OF VINYL ADHESIVE  PUT AN 8-INCH HORIZONTAL STRIP OF VINYL ADHESIVE 
TAPE OVER THE SIDES OF THE BARRICADE TAPE,  TAPE OVER THE BARRICADE TAPE BELOW THE STATIC 
OVERLAPPING THE TOP STRIP OF ADHESIVE TAPE  PORT HOLES OVERLAPPING, THE TWO VERTICAL STRIPS 

Alternate and Elevator Feel Static Port Covers Procedure
Figure 202 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 10-11-01
 ALL  ú ú 02 Page 209 ú May 20/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H23753
A

757
MAINTENANCE MANUAL

BARRICADE 
TAPE 
8-INCH STRIP OF 
VINYL ADHESIVE 
TAPE 
STEP 5  STEP 6 
CAREFULLY GRASP THE FREE SECTION OF  PLACE AN 8-INCH STRIP OF VINYL ADHESIVE 
BARRICADE TAPE, AND FOLD IT BACK  TAPE HORIZONTALLY OVER THE BACK SIDE OF THE 
AGAINST THE SURFACE OF THE AIRPLANE  BARRICADE TAPE, OVERLAPPING THE LOWER HALF 
OF THE FIRST 8-INCH STRIP OF ADHESIVE TAPE 

8-INCH STRIP OF VINYL ADHESIVE TAPE
8-INCH STRIP OF VINYL ADHESIVE TAPE
STEP 7  STEP 8
PUT AN 8-INCH STRIP OF VINYL PUT AN 8-INCH STRIP OF VINYL ADHESIVE TAPE HORIZONTALLY OVER ADHESIVE TAPE HORIZONTALLY OVER THE BARRICADE TAPE HALFWAY DOWN THE LOWER END OF THE BARRICADE TAPE THE LENGTH OF THE BARRICADE TAPE
Alternate and Elevator Feel Static Ports Cover Procedure
Figure 202 (Sheet 2)

H23459
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 10-11-01
 ALL  ú ú 04 Page 210 ú May 20/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 (c)  
Put an 8-inch strip of 3M No. 471 yellow vinyl adhesive tape on each vertical edge of the barricade tape overlapping the first strip of adhesive tape (see Fig. 203 Sheet 1, Step 3).

 (d)  
Put an 8-inch strip of 3M No. 471 vinyl adhesive tape horizontally over the barricade tape below the lower static port holes, overlapping the two vertical strips of adhesive tape (see Fig. 203 Sheet 1, Step 4).

 (e)  
Carefully grasp the free section of the barricade tape and fold it back up against the surface of the airplane. Place an 8-inch strip of 3M No. 471 vinyl adhesive tape horizontally over the back side of the barricade tape overlapping the lower half of the first horizontal strip of 8-inch 3M No. 471 vinyl adhesive tape (see Fig. 203 Sheet 2, Steps 5 and 6).

 (f)  
Allowing the baricade tape to stream down, place an 8-inch strip of 3M No. 471 yellow vinyl adhesive tape horizontally over the barricade tape half way down the length of the barricade tape (see Fig. 203 Sheet 2, Step 7).

 (g)  
Place an 8-inch strip of the 3M No. 471 yellow vinyl adhesive tape horizontally over the lower end of the barricade tape (see Fig. 203 Sheet 2, Step 8).

 S 842-031
 (20)
 Attach a red paper tag that has "STATIC PORTS COVERED" printed on it in black letters, to the left control wheel in the flight deck with wire.

 S 492-021

 (21)
 Place the cover on the angle of attack sensor.

 S 492-034

 (22)
 Place a cover on the ice detector probe if installed

 (23)
 Place a cover on the total air temperature (TAT) probe.

 S 582-018

 (24)
 Make sure that the airplane center of gravity is forward of
 59.8% MAC.

 S 492-036
 E. Put the Airplane Back In Its Usual Condition for Return to Service
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 PARKING, MOORING, STORAGE & RETURN TO S(5)