(b)
Push the switch module into the case.
NOTE: Put the side that has the word TOP in the up position.
____
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-02
ALL ú ú 03 Page 209 ú Sep 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
CAUTION: DO NOT USE THE JACKSCREW TO PULL THE SWITCH MODULE INTO
_______ ITS POSITION. THIS CAN CAUSE DAMAGE TO THE SWITCH MODULE AND CASE.
(c) Push the switch module with your finger while you lightly turn the jackscrew clockwise. 1) Continue to push the switch module and turn the jackscrew
clockwise until the jackscrew is tight.
S 862-031
CAUTION:_______DO NOT USE A DIFFERENT LAMP PART NUMBER. THE INCORRECT LAMP CAN CAUSE DAMAGE TO THE MCP.
(3)
To install a new lamp, put the lamp into the rear of the lens module.
S 432-032
(4)
To install the lens module, do these steps:
(a)
Put the link pin into the rear of the groove on the bail plate and pull the link pin to the other end of the groove.
(b)
Push the lens module into the switch module.
NOTE: Put the side that has the word TOP in the up position.
____
E. Test the mode select switch and lamp.
S 862-033
(1)
Supply the electrical power (AMM 24-22-00/201).
S 862-034
(2)
Set the two F/D switches on the MCP to OFF.
S 862-035
(3)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a) P11 Overhead Circuit Breaker Panel
1) 11E16, MODE CONT PNL LEFT
2) 11E34, MODE CONT PNL RIGHT
3) 11N30, INSTRUMENT & PANEL GLARESHIELD
4) 11P1, IND LTS L 1
5) 11P2, IND LTS L 2
6) 11P28, IND LTS R 1
7) 11P29, IND LTS R 2
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-02
ALL ú ú 03 Page 210 ú Jan 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
(4) S 712-036Do MCDP ground test 04-MCP (AMM 22-00-02/201). (a) Make sure no failures occur during test.
(5) S 862-037Remove the electrical power if it is not necessary (AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-02
ALL ú ú 01 Page 211 ú Jan 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
AUTOPILOT DISENGAGE SWITCHES - REMOVAL/INSTALLATION
___________________________________________________
1. General_______
A. One autopilot disengage switch is found on each control wheel. The removal and installation tasks for each switch are the same.
TASK 22-11-03-004-001
2. Remove the Autopilot Disengage Switch (Fig. 401)_____________________________________
A. Equipment
(1) Insertion and Extraction tool (Duetch
No. M15570-20)
B. Consumable Materials
(1) Threading wire, a 30-inch length of standard
wire (No. 18 to 22 gage), without insulation if
possible (used to pull the wire bundle through
the control wheel)
C. Access
(1) Location Zone
211/212 Flight Compartment
D. Prepare for Removal
S 864-002
(1)
Set the two F/D switches on the MCP to OFF.
S 864-003
(2)
Open these circuit breakers on the overhead circuit breaker panel, P11, and attach DO-NOT-CLOSE tags:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 1(111)
