12-20-00 Page 12-32 Revised: February 28, 2002
1G8

12-20-00 Page 12-33 Revised: February 28, 2002
COMPONENT LUBRICANT  FREQUENCY 
1. DOOR & COWL SEALS - SEE SPECIAL INSTRUCTION 6 CARBON DIOXIDE RELEASE AGENT DRY LUBRICANT MS-122N/CO2  AS REQUIRED 
2. NOSE CONE & NOSE DOOR HINGES, BAGGAGE & MAIN DOOR HINGES SEE SPECIAL INSTRUCTION 6 MIL-L-7870  100 HRS 
3. PILOT & COPILOT SEAT ADJUSTMENT SEE SPECIAL INSTRUCTION 6 AND NOTE 1 MIL-G-7711  500 HRS 
4. DOOR LATCH MECHANISM SEE SPECIAL LUBRIPLATE #907, INSTRUCTION 6 FISKE BROS. REFINING CO.  500 HRS 
SPECIAL INSTRUCTIONS 6. Lubrication Points - Wipe all lubrication points clean of old grease, oil. dirt, etc., before lubricating NOTES 1. Pilot and Passenger Seats - Lubricate track rollers and stop pins as required (Type of lubricant: MIL-L-7870). 

12-20-00 Page 12-34 Revised: February 28, 2002
1G10
CHART 1201.  THREAD LUBRICANTS

TYPE OF LINE  TYPE OF LUBRICANT 
Brakes Freon Fuel Landing Gear (Air Valve) Oil Pitot and Static  MIL-H-5606 TT-A-580 or MIL-T-5544, Anti-Seize Compound MIL-T-5544, Anti-Seize, Graphite Petrolatum 6PB Parker MIL-G-6032, Lubricating Grease (Gasoline and Oil Resistant) TT-A-580 (JAN-A-669), Anti-Seize Compund (White Lead Base) 

— Note —
Lubricate engine fittings only with the fluid contained in the particular lines.

12-20-00 Page 12-35 Revised: February 28, 2002
THIS PAGE INTENTIONALLY BLANK

12-20-00 Page 12-36 Revised: February 28, 2002
1G12

CHAPTER

20

STANDARD PRACTICES -
AIRFRAME

THIS PAGE INTENTIONALLY BLANK

CHAPTER 20 - STANDARD PRACTICES - AIRFRAME 
TABLE OF CONTENTS / EFFECTIVITY 
CHAPTER/ SECTION  SUBJECT  GRID NO.  EFFECTIVITY 
20-00-00  STANDARD PRACTICES - AIRFRAME  1G17 
Torque Wrenches Method of Installing Rod End Bearings Cherrylock Rivets, Removal Identification of Fluid Lines  1G17 1G18 1G19 1G20  1R0202 

20-Cont./Effec. Page 20-3 Revised: February 28, 2002
THIS PAGE INTENTIONALLY BLANK

20-Cont./Effec. Page 20-4 Revised: February 28, 2002
1G16
STANDARD PRACTICES - AIRFRAME.
TORQUE WRENCHES.
Torque wrenches should be checked daily and calibrated by means of weights and a measured lever arm to make sure that inaccuracies are not present.  Checking one torque wrench against another is not sufficient and is not recommended. Some wrenches are quite sensitive as to the way they are supported during a tightening operation. Any instructions furnished by the manufacturer must be followed explicitly.
When it is necessary to use a special extension or adapter wrench together with a torque wrench, a simple mathematical equation must be worked out to arrive at the correct torque reading.  Following is the formula to be used: (Refer to Figure 20-1)
T = Torque desired at the part.
A = Basic lever length from center of wrench shank to center of handle or stamped on wrench or listed

for that model wrench. B = Length of adapter extension, center of bolt to center of shank. C = Scale reading needed to obtain desired torque (T).
A x T The formula: C =
A + B EXAMPLE A bolt requires 30 foot pounds and a 3 inch adapter (one-quarter of a foot or .25‘) is needed to get at it. You want to know what scale reading it will take on a one-foot lever arm wrench to obtain the 30 foot pounds at the bolt.
C = 1 x 30 30or C = = 24 ft.-lbs.
1 + .25 1.25 Remember the 3 inch adapter must be projecting 3 inches straight along the wrench axis. In general avoid all complex assemblages or adapters and extensions of flex joints.

20-00-00 Page 20-5 Revised: February 28, 2002
METHOD OF INSTALLING ROD END BEARINGS.

20-00-00 Page 20-6 Revised: February 28, 2002
1G18
CHERRYLOCK RIVETS, REMOVAL. (Refer to Figure 20-3.)
Should it be necessary to remove an installed cherrylock
rivet, the following procedures are recommended. In thick material remove the lock by driving out the rivet stem, using a tapered steel drift pin. (See View 1)
— Note —
Do not drill completely through the rivet sleeve to remove a rivet as this will tend to enlarge the hole.
2.  
If the rivets have been installed in thin sheets, driving out the locked stem may damage the sheets.  It is recommended that a small center drill be used to provide a guide for a larger drill on top of the rivet stem, and the tapered portion of the stem be drilled away to destroy the lock. (See Views 2 and 3)

3.  
Pry the remainder of the locking collar out of the rivet head with the drift pin. (See View 3)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西門諾爾飛機維護手冊 simenole PA-44-180 AMM 1(35)