曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

E.  Should tension be incorrect, loosen the turnbuckle of the lower cable in the aft section of the fuse-lage and adjust the turnbuckle of the upper cable to obtain correct tension. Cable tension should be obtained with control wheel at the one-quarter inch dimension from the stop and the stabilator contacting its stop.
F.  Check safety of all turnbuckles and bolts.
G.  With the tension of the upper cable correct and the control wheel still forward, adjust the turn-buckle of the lower cable to obtain correct tension.
H.  Check the full travel of the control wheel with relation to the full travel of the stabilator to deter-mine that the stabilator contacts its stops before the control wheel contacts its stops. With the control wheel in the fore and aft positions, the travel distance from the joint where the stabilator contacts its stops and the control wheel contacts its stops should be approximately equal. Readjust turnbuckles if incorrect.
I.  Connect the assist springs to bulkhead sta. 156. (Refer to-Figure 27-18.)
J.  Install access panels and fin tip.
27-30-00 Page 27-45 Issued: April 1, 1997 27-30-00 Page 27-46 Issued: April 1, 1997

PAGES 2C23 AND 2C24 INTENTIONALLY BLANK

27-30-00 Page 27-47 Issued: April 1, 1997
THIS PAGE INTENTIONALLY BLANK

27-30-00 Page 27-48 Issued: April 1, 1997
STABILATOR TRIM.
REMOVAL OF FORWARD STABILATOR TRIM ASSEMBLY.  (Refer to Figure 27-22.)

1.  
To remove the trim control wheel assembly and/or the trim control cables, remove the panel to the aft section of the airplane.

2.  
If the aft trim cable is not to be removed, block the cables at the pulleys in the aft section of the fuselage to prevent them from unwrapping from the trim drum. (Refer to Figure 27-21.)

3.  
If the trim control wheel and cables are to be removed, loosen or disconnect the cables at the trim cable turnbuckles in the aft section of the fuselage.

4.  
To remove the control wheel with drum:

A.  Remove the control wheel cover by removing the cover attaching screws.
B.  The wheel assembly may be removed from its mounting brackets by removing nut, washer and bolt that secures the wheel between the brackets. Draw the wheel from the brackets. Use caution not to damage trim indicator wire.
C.  Unwrap the left cable from the drum.
D.  The wheel and drum are joined by a push fit, separate these two items with their center bushing and unwrap the right cable.
E.  Tie the cables forward to prevent them from slipping back into the floor tunnel.
5.  To remove the trim control cables:
A.  Remove the pilot and rear seats if desired.
B.  Remove the seat belts attached to the forward floor tunnel by removing attachment nuts, washers and bolts.
C.  Remove the heater deflectors from each side of the aft end of the forward floor tunnel by sliding the deflector sideways and releasing the retainer spring.
D.  Unfasten the carpet from the aft portion of the forward floor tunnel and lay it forward.
E.  Remove the tunnel cover located between the trim control wheel and the spar cover by removing the selector knobs and cover attachment screws.
F.  Remove the cable pulleys located in the forward tunnel by removing the cotter pin, washer and clevis pin.
G.  Remove the floor panel aft of the main spar by removing the panel attachment screws and seat belt attachments. Lift the panel and remove from airplane.
H.  Remove the cable rub blocks located in the floor opening on the aft side of the main spar by removing the block attachment screws.
I.  Remove the trim plate located on top of the forward end of the aft floor tunnel.
J.  Remove the carpet from the aft floor tunnel.
K.  Remove the cover plate from the top of the aft floor tunnel by removing attachment screws.
L.  Remove the cable guard from the underside of the trim cable pulleys located in the forward area of the aft floor tunnel by removing a tinnerman nut and withdrawing the cable guard.
M.  Remove the cable guard plate from the underside of the pulley cluster located in the aft area of the floor tunnel by removing the plate attachment screws.
N.  Remove the cable guard from the cable pulleys in the aft lower section of the fuselage forward of the cable turnbuckles.
O.  With the cables disconnected from the trim control wheel, draw the cable(s) through the floor tunnel.
27-30-00 Page 27-49 Issued: April 1, 1997

Figure 27-22. Stabilator Trim Controls 
27-30-00 
Page 27-50 
Issued: April 1, 1997 
2D3 

INSTALLATION OF FORWARD STABILATOR TRIM ASSEMBLY.  (Refer to Figure 27-22.)
1.  The trim control wheel with drum may be installed by the following procedure:
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西門諾爾飛機維護手冊 simenole PA-44-180 AMM 1(86)