Introduction Page 16
Revised: December 6, 2002
2A20
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL
LIST OF ILLUSTRATIONS (cont)
FIGURE N0. SUBJECT GRID NO.
51-1. Skin Materials and Thickness (Sheet 1 of 2) 3B18
51-1. Skin Materials and Thickness (Sheet 2 of 2) 3B19
51-2 Surface Scratches, Abrasions or Ground-in-Dirt 3C2
51-3. Deep Scratches, Shallow Nicks and Small Holes 3C3
51-4. Mixing of Epoxy Patching Compound 3C3
51-5. Welding Repair Method 3C4
51-6. Repairing of Cracks 3C4
51-7. Various Repairs 3C5
51-8. Repair of Stress Lines 3C7
51-9. Repair of Impacted Damage 3C7
52-1. Door Snubber Installation 3C13
52-2. Door Installation 3C17
52-3. Emergency Exit Installation 3C21
52-4. Fabricated Tool for Baggage Door Lock 3C23
55-1. Stabilator Installation 3D7
55-2. Stabilator Balance Configuration 3D8
55-3. Vertical Stabilizer Installation 3D10
55-4. Rudder Installation 3D13
55-5. Rudder Balancing 3D14
56-1. Windshield Installation 3D23
56-2. Side Window Installation 3E3
57-1. Wing Installation 3E13
57-2. Aileron and Flap Installation 3E19
57-3. Aileron Balancing 3E21
57-4. Aileron Skin Repair 3E22
61-1. Typical Nicks and Removal Method 3F6
61-2. Propeller Installation 3F7
61-3. Propeller Governor (Sheet 1 of 2) 3F10
61-3. Propeller Governor (Sheet 2 of 2) 3F10
61-4. Propeller Unfeathering System 3F13
71-1. Engine and Shock Mount Installation 3G3
71-2. Engine Cowling Installation 3G7
71-3. Cowl Flap Installation 3G7
71-4. Induction System 3G13
73-1. Carburetor 3G19
73-2. Fuel System Schematic 3G22
73-3 Adjustment of Engine Controls 3H1
74-1. Contact Points 3H12
74-2. Slick T-100 Assembly and Timing Tool Kit 3H13
74-3. Removing Coil Wedges 3H14
74-4. Exploded View of Slick 4300 Series Magneto 3H15
74-5. Index Plate and Timing Plug 3H17
Introduction Page 17 Revised: December 6, 2002
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL
LIST OF ILLUSTRATIONS (cont)
FIGURE NO. SUBJECT GRID NO.
74-6. Installation of Bearings 3H17
74-7. Magneto Oil Seal Installation on T-125 Assembly Fixture 3H19
74-8. Magneto Internal Timing 3H19
74-9. Engine Timing Marks 3H21
74-10. Stipping Tool 3I2
74-11. Inserting Stipping Tool 3I2
74-12. Cutting Insulation 3I2
74-13. Removing Silicone Rubber from Wire 3I2
74-14. Installation of Plug Endnut 3I3
74-15. Flaring out the Shielding 3I3
74-16. Installation of Ferrule 3I3
74-17. Driving Tool 3I3
74-18. Insulation in Harness Cap 3I5
74-19. Securing Wire in Harness Cap 3I5
74-20. Installation of Electrode Screw 3I5
74-21. Installation of Insulator Sleeve 3I5
74-22. Installation of Spring 3I6
74-23. Removing Spark Plug Frozen to Bushing 3I6
74-24. Magneto and Starter Switches 3I9
77-1. Engine Instrument Lines Installation 3I15
77-2. Electric Tachometer Installation 3I19
77-3. Cylinder Head Temperature Gauge Calibration 3I22
78-1. Inspection of Mufflers 3J5
79-1. Oil Pressure Gauge Calibration 3J14
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：西門諾爾飛機維護手冊 simenole PA-44-180 AMM 1(70)
