曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

BEJ 001-007 PRE SB 777-52-0031
Either the external or internal handle closes the door. The secondary lift and latch cranks lower the door into the plug position inboard of the cutout stops (not shown). The drive rod pushes the vent door closed.
BEJ ALL
The girt bar mechanism interlock releases the end crank.
Arm
Aft movement of the mode select handle closes the mode select switch. This arms the EPAS electric power circuit. The movement also releases the girt bar from the girt bar mechanism. The floor fitting assembly locks the bar to the floor.
EFFECTIVITY BEJ ALL  52-11-00 
Page 52 
D633W101-BEJ  May 05/2003 

 

PASSENGER ENTRY DOOR SYSTEM -FUNCTIONAL DESCRIPTION

EFFECTIVITY BEJ 008-999; BEJ 001-007 POST SB 777-52-0031  52-11-00 
Page 53 
D633W101-BEJ  May 05/2003 

 

PASSENGER ENTRY DOOR SYSTEM -FUNCTIONAL DESCRIPTION

EFFECTIVITY BEJ 001-007 PRE SB 777-52-0031  52-11-00 
Page 54 
D633W101-BEJ  May 05/2003 

PASSENGER ENTRY DOOR SYSTEM -OPERATION

General
There are markers on the door that tell you the direction to move the handles for door operation.
External Open Operation
Pull the external handle outboard. This moves the mode select handle to the MANUAL position if it has not already been set to that position.
Turn the handle 180 degrees in the open direction. The vent door should open as you start to turn the handle. The door will move inboard and upward as you continue to turn the handle. The external handle stays in the extended position while the door is open.
Pull the door outboard and push it forward until it stops. Do a check to see that the hold-open hook has engaged the hold-open catch.
External Close Operation
Do a check to see that the door area and girt bar floor fitting are not blocked.
If the external handle is not in the extended position, pull it outboard and rotate it 180 degrees. It will stay extended outboard.
EFFECTIVITY
BEJ ALL

Push the door forward and pull the hold-open release handle on the inside of the door. This releases the door hold-open hook. Pull and push the door toward the closed position. Use the extended, external handle to push the door inboard into the cabin.
Turn the external handle 180 degrees in the closed direction. The door will move downward and slightly outboard as it goes to the closed position. The vent door should close as you complete the door handle movement. The door is now closed, latched, and locked.
The handle is spring loaded and moves inboard to the faired position at the end of the rotation.
When you turn the external handle to close the door, it does not move the mode select handle to the AUTO position.
If the handle will not turn to the closed position, do a check of the door system.
Internal Open Operation
Move the mode select lever to the MANUAL position. Do a check of the two witness ports in the sidewall near the bottom of the door. The yellow door armed indication flags should not show.
If either flag shows, do not use the door. Do a system check.
52-11-00

Page 55 D633W101-BEJ May 05/2003

PASSENGER ENTRY DOOR SYSTEM -OPERATION

Move the internal handle to the open position. Push outboard and forward on the door. When the door stops, do a check to see that the hold-open hook has engaged the hold-open catch.
Internal Close Operation
Do a check to see that the door area and girt bar floor fitting are not blocked. Push the door forward and pull on the hold-open release handle to release the door hold-open hook. Move the door into the cabin.
Turn the internal door handle in the closed direction. If the handle will not turn to the closed position, do a check of the door system.
Training Information Point
A safety switch on the EPAS battery lets you stop the EPAS operation when you do door maintenance. You cannot close the hinge cover when the switch is in the safe position.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：777 AMM 飛機維護手冊 Doors 艙門(15)