曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(1)  Examine the ELT and the ELT mounting tray, look specially for: S Security of the fasteners. S Security of all mechanical assemblies. 
(2)  Examine the Co-axial cable from the ELT to the antenna. Look specially for: S Cuts or abrasions to the outer sheath of the co-axial cable. 
(3)  Disconnect the co-axial cable from the antenna and the ELT. Examine the connectors at each end of the co-axial cable, the antenna and the ELT for corrosion or damage. Reconnect the co-axial cable. 
(4)  Examine the modular cable which connects the ELT to the RCPI. Look specially for: S Cuts or abrasions to the outer sheath of the cable. 
(5)  Disconnect the modular cable from both the ELT and the RCPI. Examine the electrical connections at each end of the modular cable for corrosion or damage. Reconnect the modular cable. 
(6)  Read the expiry dates of the system batteries and replace the batteries if necessary.  Refer to Paragraph 4 and Paragraph 6. 
(7)  Remove the battery case from the ELT.  Refer to Paragraph 4. 

Doc # 6.02.01 Page 211
Rev. 4 09 Jan 2003

25-60-00
AMM

%
%

Detail Steps/Work Items  Key Items/References 
(8)  Examine the battery compartment. Look specially for: S Corrosion of the battery spring clips. S Battery leakage.  If one battery leaks, then you must replace all batteries. 
(9)  Install the battery case to the ELT.  Refer to Paragraph 4. 
(10)  Do a function test of the ELT system.  Refer to Paragraph 3. 

25-60-00
DA 40 Series
Equipment/Furnishings

%

%
%

%

%
%

%
%

%
%
%

%
%
%
%

%

%
%

%
%
%

%
%

%

% B. Jolliet JE2-NG %

Detail Steps/Work Items  Key Items/References 
(1)  Examine the ELT and the ELT mounting tray, look specially for: S Security of the fasteners. S Security of all mechanical assemblies. 
(2)  Examine the co-axial cable from the ELT to the antenna. Look specially for: S Cuts or abrasions to the outer sheath of the co-axial cable. 
(3)  Disconnect the co-axial cable from the antenna and the ELT. Examine the connectors at each end of the co-axial cable, the antenna and the ELT for corrosion or damage. Reconnect the co-axial cable. 
(4)  Examine the cable which connects the ELT to the RCS. Look specially for: S Cuts or abrasions to the outer sheath of the cable. 
(5)  Read the expiry date of the system battery and replace the battery if necessary.  Refer to Paragraph 4. 
(6)  Do a function test of the ELT system.  Refer to Paragraph 3. 

Doc # 6.02.01 Page 213
Rev. 4 09 Jan 2003

25-60-00
AMM

Intentionally left blank
25-60-00
Fire Protection
AMM

CHAPTER 26
 FIRE PROTECTION

Doc # 6.02.01 Page 1
Rev. 4 09 Jan 2003

26-TITLE
AMM

Intentionally left blank
26-TITLE
Fire Protection
AMM

TABLE OF CONTENTS
CHAPTER 26
FIRE PROTECTION - GENERAL

1.
General ..............................................1

2.
Description............................................1

 

Doc # 6.02.01 Page 1
Rev. 4 09 Jan 2003

26-CONTENTS
AMM

Intentionally left blank
26-CONTENTS
Fire Protection
AMM

CHAPTER 26
FIRE PROTECTION - GENERAL

1. General
This Chapter tells you only about the fire extinguisher installed in the airplane. See the fire extinguisher manufacturer's manual for more data about the extinguisher.
Note:  Equipment which is certified for installation in the DA 40 is listed in Section 6.5 of the Airplane Flight Manual. Such equipment may be installed in accordance with the Airplane Maintenance Manual.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 2(84)