曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

14.2  The pilot shall provide confirmation of the performance of the navigational aids used for the IAP (2301).  The ATS provider shall formally record this confirmation (2302).
Table 1 Azimuth Limits Table 1 Azimuth Limits (Continued) Table 1 Azimuth Limits (Continued) Table 1 Azimuth Limits (Continued) Table 1 Azimuth Limits (Continued) Table 2 Elevation Limits Table 2 Elevation Limits (Continued) Table 2 Elevation Limits (Continued)
Parameter  Tolerance  Profile  Measurement to be made  Transmitter tobe checked 
AngleAccuracyRunwayCoverage Area to ApproachReference Datum (ARD)  Path Following Error (PFE) ± 4.0mPath Following Noise (PFN)  ± 3.5mControl Motion Noise (CMN) ± 3.2m or 0.1 degree,whichever is less  Ground checkOn centreline between ARD and along runway  From plot  CommissioningBothRoutineBoth 
Mean Course Error (MCE) ± 3.0mNote: The ICAO Standard in Annex 10 Volume 1 paragraph 3.11.5.2.5.1 is for ground equipmentcontribution. Checks in the far field would include the effects of multipath.  Due to the similarity withILS it is assumed that this requirement includes multipath effects.MCE standard needs to be clarified by ICAO.  Ground CheckSpot check at the ARD  Direct reading 
AngleAccuracyARD to limits of coverage  PFE and PFN The PFE and PFN limits, expressed in angular terms at 37 km (20 NM) from the runway threshold along the extended runway centre line, shall degrade linearly to be 2 times the value specifiedat the ARD  This is a two-part testLevel slice on centre line from 20NM at 0.3 theta to 1.75 thetaNote: The requirement for flight to1.75 theta can be reduced ifelevation is not being checked.Fly down from 7 NM on azimuth and elevation to ARD  Plot from 20 NM to the intercept of the glidepath;andPlot from 6 NM to ARD  CommissioningBothRoutineBoth 
CMNThe CMN limit shall degrade linearly from the value at ARD to be 0.1 degree at 37 km (20 NM) from theARD along the extended runway centre line at theminimum glide path angle
MCEThe Mean Course Error shall not exceed an errorequivalent to ± 3.0m at ARD  Fly down from 7 NM on azimuth and elevation to ARD  Average between 1NM and ARD 

Parameter  Tolerance  Profile  Measurement to be made  Transmitter tobe checked 
AngleAccuracywith Azimuth Angle  PFE and PFNThe PFE and PFN limits, expressed in angular terms at plus or minus 40 degrees azimuth angle,shall degrade linearly to be 1.5 times the value onthe extended runway centreline at the samedistance from the ARDThe PFE limits shall not exceed 0.25 degree in any region of coverageThe PFN limits shall not exceed 0.15 degree in anyregion of coverageNote: When clearance is used, PFE and PFN can only be measured in the proportional guidance area  2 flights, one either side of the centreline, in the vicinity of the edge of the proportional guidanceEach flight comprising a level slice from 20 NM at 0.3 theta to a pointto intersect the glide path angle and then fly down to ARD  Plot from 20 NM to ARD  Commissioningonly.One TX 
CMNThe CMN limit, expressed in angular terms at plus or minus 40 degrees azimuth angle, shall degradelinearly to be 1.3 times the value on the extendedrunway centreline at the same distance from the ARDThe CMN limits shall not exceed 0.1 degree in any region of coverageNote: When clearance is used, CMN can only bemeasured in the proportional guidance area 

Parameter  Tolerance  Profile  Measurement to be made  Transmitter tobe checked 
ClearanceRegions  Fly left or fly right clearance information asappropriate from beyond the proportional guidancesector to ± 40 degrees  CommissioningPart orbit at not less than 5NM from ARD at Minimum SafeAltitude (MSA) in both directionsRoutinePart orbit at not less than 5NM from ARD at Minimum SafeAltitude (MSA) in one direction  Plot from ± 40 degrees about centreline  CommissioningBothRoutineBoth 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：CAP 670 Air Traffic Services Safety Requirements 2(52)